KDMB - Ball Nose Finisher - End Mills - Inch 2878446

Feeds

KDMB Ball Nose • .250"

	Diametro di lavorazione (Dw) alla profondità di taglio assiale (ap)
D1 max	0.125	0.050	0.025	0.013
0.250	0.250	0.200	0.150	0.109

At .125 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP

At .050 Axial Depth of Cut (ap)

Lavorazione leggera

Uso generico

Lavorazione pesante

At .025 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP

At .013 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.006	.008	.015	.004	.006	.011	.004	.005	.010	.004	.005	.009	.004	.005	.009	.E..LD
.E..GP	.006	.008	.015	.004	.006	.011	.004	.005	.010	.004	.005	.009	.004	.005	.009	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP

Lavorazione leggera

Uso generico

Lavorazione pesante

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.006	.008	.015	.004	.006	.011	.004	.005	.010	.004	.005	.009	.004	.005	.009	.E..LD
.E..GP	.006	.008	.015	.004	.006	.011	.004	.005	.010	.004	.005	.009	.004	.005	.009	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP

KDMB Ball Nose • .312"

	Diametro di lavorazione (Dw) alla profondità di taglio assiale (ap)
D1 max	0.156	0.047	0.031	0.016
0.313	0.313	0.223	0.188	0.136

At .156 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP

At .047 Axial Depth of Cut (ap)

Lavorazione leggera

Uso generico

Lavorazione pesante

At .031 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP

At .016 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP

Lavorazione leggera

Uso generico

Lavorazione pesante

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP

KDMB Ball Nose • .375"

	Diametro di lavorazione (Dw) alla profondità di taglio assiale (ap)
D1 max	0.188	0.056	0.038	0.019
0.375	0.375	0.268	0.225	0.163

At .188 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP

At .056 Axial Depth of Cut (ap)

Lavorazione leggera

Uso generico

Lavorazione pesante

At .038 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP

At .019 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP

Lavorazione leggera

Uso generico

Lavorazione pesante

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP

KDMB Ball Nose • .500"

	Diametro di lavorazione (Dw) alla profondità di taglio assiale (ap)
D1 max	0.250	0.075	0.050	0.025
0.500	0.500	0.357	0.300	0.218

At .250 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP
.E..GN	.007	.010	.018	.005	.008	.013	.004	.007	.011	.004	.006	.011	.004	.006	.011	.E..GN
.E..HC	.007	.014	.024	.005	.010	.018	.004	.009	.015	.004	.008	.014	.004	.008	.014	.E..HC

At .075 Axial Depth of Cut (ap)

Lavorazione leggera

Uso generico

Lavorazione pesante

At .050 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP
.E..GN	.016	.024	.042	.012	.017	.031	.010	.015	.026	.009	.014	.025	.009	.014	.024	.E..GN
.E..HC	.016	.032	.057	.012	.023	.041	.010	.020	.035	.009	.019	.033	.009	.018	.032	.E..HC

At .025 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP
.E..GN	.009	.014	.025	.007	.011	.019	.006	.009	.016	.006	.009	.015	.006	.008	.015	.E..GN
.E..HC	.009	.019	.034	.007	.014	.025	.006	.012	.021	.006	.011	.020	.006	.011	.020	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP
.E..GN	.011	.017	.030	.008	.013	.022	.007	.011	.019	.007	.010	.018	.007	.010	.018	.E..GN
.E..HC	.011	.023	.041	.008	.017	.030	.007	.015	.026	.007	.014	.024	.007	.013	.023	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP
.E..GN	.007	.010	.018	.005	.008	.013	.004	.007	.011	.004	.006	.011	.004	.006	.011	.E..GN
.E..HC	.007	.014	.024	.005	.010	.018	.004	.009	.015	.004	.008	.014	.004	.008	.014	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP
.E..GN	.009	.014	.025	.007	.011	.019	.006	.009	.016	.006	.009	.015	.006	.008	.015	.E..GN
.E..HC	.009	.019	.034	.007	.014	.025	.006	.012	.021	.006	.011	.020	.006	.011	.020	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP
.E..GN	.016	.024	.042	.012	.017	.031	.010	.015	.026	.009	.014	.025	.009	.014	.024	.E..GN
.E..HC	.016	.032	.057	.012	.023	.041	.010	.020	.035	.009	.019	.033	.009	.018	.032	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP
.E..GN	.011	.017	.030	.008	.013	.022	.007	.011	.019	.007	.010	.018	.007	.010	.018	.E..GN
.E..HC	.011	.023	.041	.008	.017	.030	.007	.015	.026	.007	.014	.024	.007	.013	.023	.E..HC

Lavorazione leggera

Uso generico

Lavorazione pesante

KDMB Ball Nose • .625"

	Diametro di lavorazione (Dw) alla profondità di taglio assiale (ap)
D1 max	0.313	0.094	0.063	0.031
0.625	0.625	0.446	0.375	0.272

At .313 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP
.E..HC	.007	.014	.024	.005	.010	.018	.004	.009	.015	.004	.008	.014	.004	.008	.014	.E..HC

At .094 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP
.E..HC	.009	.019	.034	.007	.014	.025	.006	.012	.021	.006	.011	.020	.006	.011	.020	.E..HC

At .063 Axial Depth of Cut (ap)

Lavorazione leggera

Uso generico

Lavorazione pesante

At .031 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP
.E..HC	.016	.032	.057	.012	.023	.041	.010	.020	.035	.009	.019	.033	.009	.018	.032	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP
.E..HC	.011	.023	.041	.008	.017	.030	.007	.015	.026	.007	.014	.024	.007	.013	.023	.E..HC

Lavorazione leggera

Uso generico

Lavorazione pesante

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP
.E..HC	.016	.032	.057	.012	.023	.041	.010	.020	.035	.009	.019	.033	.009	.018	.032	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP
.E..HC	.007	.014	.024	.005	.010	.018	.004	.009	.015	.004	.008	.014	.004	.008	.014	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP
.E..HC	.009	.019	.034	.007	.014	.025	.006	.012	.021	.006	.011	.020	.006	.011	.020	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP
.E..HC	.011	.023	.041	.008	.017	.030	.007	.015	.026	.007	.014	.024	.007	.013	.023	.E..HC

KDMB Ball Nose • .750"

	Diametro di lavorazione (Dw) alla profondità di taglio assiale (ap)
D1 max	0.375	0.113	0.075	0.038
0.750	0.750	0.536	0.450	0.327

At .375 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP
.E..GN	.007	.010	.018	.005	.008	.013	.004	.007	.011	.004	.006	.011	.004	.006	.011	.E..GN
.E..HC	.007	.014	.024	.005	.010	.018	.004	.009	.015	.004	.008	.014	.004	.008	.014	.E..HC

At .113 Axial Depth of Cut (ap)

Lavorazione leggera

Uso generico

Lavorazione pesante

At .075 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP
.E..GN	.009	.014	.025	.007	.011	.019	.006	.009	.016	.006	.009	.015	.006	.008	.015	.E..GN
.E..HC	.009	.019	.034	.007	.014	.025	.006	.012	.021	.006	.011	.020	.006	.011	.020	.E..HC

At .038 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP
.E..GN	.016	.024	.042	.012	.017	.031	.010	.015	.026	.009	.014	.025	.009	.014	.024	.E..GN
.E..HC	.016	.032	.057	.012	.023	.041	.010	.020	.035	.009	.019	.033	.009	.018	.032	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP
.E..GN	.011	.017	.030	.008	.013	.022	.007	.011	.019	.007	.010	.018	.007	.010	.018	.E..GN
.E..HC	.011	.023	.041	.008	.017	.030	.007	.015	.026	.007	.014	.024	.007	.013	.023	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP
.E..GN	.009	.014	.025	.007	.011	.019	.006	.009	.016	.006	.009	.015	.006	.008	.015	.E..GN
.E..HC	.009	.019	.034	.007	.014	.025	.006	.012	.021	.006	.011	.020	.006	.011	.020	.E..HC

Lavorazione leggera

Uso generico

Lavorazione pesante

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP
.E..GN	.016	.024	.042	.012	.017	.031	.010	.015	.026	.009	.014	.025	.009	.014	.024	.E..GN
.E..HC	.016	.032	.057	.012	.023	.041	.010	.020	.035	.009	.019	.033	.009	.018	.032	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP
.E..GN	.011	.017	.030	.008	.013	.022	.007	.011	.019	.007	.010	.018	.007	.010	.018	.E..GN
.E..HC	.011	.023	.041	.008	.017	.030	.007	.015	.026	.007	.014	.024	.007	.013	.023	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP
.E..GN	.007	.010	.018	.005	.008	.013	.004	.007	.011	.004	.006	.011	.004	.006	.011	.E..GN
.E..HC	.007	.014	.024	.005	.010	.018	.004	.009	.015	.004	.008	.014	.004	.008	.014	.E..HC

KDMB Ball Nose • 1.00"

	Diametro di lavorazione (Dw) alla profondità di taglio assiale (ap)
D1 max	0.500	0.150	0.100	0.050
1.000	1.000	0.714	0.600	0.436

At .500 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP
.E..GN	.007	.010	.018	.005	.008	.013	.004	.007	.011	.004	.006	.011	.004	.006	.011	.E..GN
.E..HC	.007	.014	.024	.005	.010	.018	.004	.009	.015	.004	.008	.014	.004	.008	.014	.E..HC

At .150 Axial Depth of Cut (ap)

Lavorazione leggera

Uso generico

Lavorazione pesante

At .100 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP
.E..GN	.009	.014	.025	.007	.011	.019	.006	.009	.016	.006	.009	.015	.006	.008	.015	.E..GN
.E..HC	.009	.019	.034	.007	.014	.025	.006	.012	.021	.006	.011	.020	.006	.011	.020	.E..HC

At .050 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP
.E..GN	.016	.024	.042	.012	.017	.031	.010	.015	.026	.009	.014	.025	.009	.014	.024	.E..GN
.E..HC	.016	.032	.057	.012	.023	.041	.010	.020	.035	.009	.019	.033	.009	.018	.032	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP
.E..GN	.011	.017	.030	.008	.013	.022	.007	.011	.019	.007	.010	.018	.007	.010	.018	.E..GN
.E..HC	.011	.023	.041	.008	.017	.030	.007	.015	.026	.007	.014	.024	.007	.013	.023	.E..HC

Lavorazione leggera

Uso generico

Lavorazione pesante

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP
.E..GN	.016	.024	.042	.012	.017	.031	.010	.015	.026	.009	.014	.025	.009	.014	.024	.E..GN
.E..HC	.016	.032	.057	.012	.023	.041	.010	.020	.035	.009	.019	.033	.009	.018	.032	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP
.E..GN	.011	.017	.030	.008	.013	.022	.007	.011	.019	.007	.010	.018	.007	.010	.018	.E..GN
.E..HC	.011	.023	.041	.008	.017	.030	.007	.015	.026	.007	.014	.024	.007	.013	.023	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP
.E..GN	.009	.014	.025	.007	.011	.019	.006	.009	.016	.006	.009	.015	.006	.008	.015	.E..GN
.E..HC	.009	.019	.034	.007	.014	.025	.006	.012	.021	.006	.011	.020	.006	.011	.020	.E..HC

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP
.E..GN	.007	.010	.018	.005	.008	.013	.004	.007	.011	.004	.006	.011	.004	.006	.011	.E..GN
.E..HC	.007	.014	.024	.005	.010	.018	.004	.009	.015	.004	.008	.014	.004	.008	.014	.E..HC

KDMB Ball Nose • 1.25"

	Diametro di lavorazione (Dw) alla profondità di taglio assiale (ap)
D1 max	0.625	0.188	0.125	0.063
1.250	1.250	0.893	0.750	0.545

At .625 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP

At .188 Axial Depth of Cut (ap)

Lavorazione leggera

Uso generico

Lavorazione pesante

At .125 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP

At .063 Axial Depth of Cut (ap)

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
	10%			20%			30%			40%			50–100%
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..LD
.E..GP	.007	.009	.017	.005	.007	.012	.004	.006	.011	.004	.006	.010	.004	.006	.010	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..LD
.E..GP	.008	.011	.020	.006	.008	.015	.005	.007	.013	.005	.007	.012	.005	.007	.012	.E..GP

Lavorazione leggera

Uso generico

Lavorazione pesante

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..LD
.E..GP	.011	.016	.028	.008	.012	.020	.007	.010	.018	.007	.009	.016	.006	.009	.016	.E..GP

Geometria dell'inserto	Avanzamento per dente programmato (fz) in base alla % della profondità di taglio radiale (ae)															Geometria dell'inserto
Geometria dell'inserto	10%			20%			30%			40%			50–100%			Geometria dell'inserto
.E..LD	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..LD
.E..GP	.005	.007	.012	.004	.005	.009	.003	.004	.008	.003	.004	.007	.003	.004	.007	.E..GP

Ulteriori informazioniView Less

Speeds

Recommended Starting Speeds [SFM]

Gruppo materiali		K115M			KC505M			KC515M			KC530M
P	1	–	–	–	–	–	–	1080	960	840	900	780	660
	2	–	–	–	–	–	–	1020	900	780	780	660	540
	3	–	–	–	–	–	–	900	780	660	660	600	540
	4	–	–	–	1180	860	710	780	660	540	600	540	480
	5	–	–	–	1180	860	710	660	540	420	540	480	420
	6	–	–	–	1140	780	620	540	420	360	420	360	300
M	1	–	–	–	–	–	–	1080	900	780	900	720	600
	2	–	–	–	–	–	–	900	720	540	600	480	420
	3	–	–	–	–	–	–	720	600	480	480	420	360
K	1	720	600	480	–	–	–	1440	1080	720	–	–	–
	2	600	480	360	–	–	–	1080	840	600	–	–	–
	3	360	300	240	–	–	–	480	360	240	–	–	–
N	1–2	1440	1080	720	–	–	–	–	–	–	–	–	–
	3	960	720	600	–	–	–	–	–	–	–	–	–
S	1	–	–	–	–	–	–	–	–	–	–	–	–
	2	–	–	–	–	–	–	–	–	–	–	–	–
	3	–	–	–	–	–	–	–	–	–	–	–	–
	4	300	230	160	–	–	–	–	–	–	260	200	170
H	1	–	–	–	860	670	550	550	400	310	–	–	–

Gruppo materiali		K115M			KC505M			KC515M			KC530M
P	1	–	–	–	–	–	–	1080	960	840	900	780	660
	2	–	–	–	–	–	–	1020	900	780	780	660	540
	3	–	–	–	–	–	–	900	780	660	660	600	540
	4	–	–	–	1180	860	710	780	660	540	600	540	480
	5	–	–	–	1180	860	710	660	540	420	540	480	420
	6	–	–	–	1140	780	620	540	420	360	420	360	300
M	1	–	–	–	–	–	–	1080	900	780	900	720	600
	2	–	–	–	–	–	–	900	720	540	600	480	420
	3	–	–	–	–	–	–	720	600	480	480	420	360
K	1	720	600	480	–	–	–	1440	1080	720	–	–	–
	2	600	480	360	–	–	–	1080	840	600	–	–	–
	3	360	300	240	–	–	–	480	360	240	–	–	–
N	1–2	1440	1080	720	–	–	–	–	–	–	–	–	–
N	3	960	720	600	–	–	–	–	–	–	–	–	–
S	1	–	–	–	–	–	–	–	–	–	–	–	–
	2	–	–	–	–	–	–	–	–	–	–	–	–
	3	–	–	–	–	–	–	–	–	–	–	–	–
	4	300	230	160	–	–	–	–	–	–	260	200	170
H	1	–	–	–	860	670	550	550	400	310	–	–	–

Ulteriori informazioniView Less

Insert Selection

KDMB Ball Nose Platform • .250"

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
–	(Geometria leggera)		–		(Geometria robusta)
–	resistenza all’usura				tenacità
–	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
P3–P4	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
P5–P6	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
M1–M2	.E..GP	KC515M	.E..GP	KC515M	–	–
M3	.E..GP	KC515M	.E..GP	KC515M	–	–
K1–K2	.E..GP	KC515M	.E..GP	KC515M	–	–
K3	.E..GP	KC515M	.E..GP	KC515M	–	–
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	–	–	.E..GP	KC515M	–	–
H1	.E..GP	KC515M	.E..GP	KC515M	–	–

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
	(Geometria leggera)		Uso generico		(Geometria robusta)
	resistenza all’usura				tenacità
	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
P3–P4	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
P5–P6	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
M1–M2	.E..GP	KC515M	.E..GP	KC515M	–	–
M3	.E..GP	KC515M	.E..GP	KC515M	–	–
K1–K2	.E..GP	KC515M	.E..GP	KC515M	–	–
K3	.E..GP	KC515M	.E..GP	KC515M	–	–
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	–	–	.E..GP	KC515M	–	–
H1	.E..GP	KC515M	.E..GP	KC515M	–	–

KDMB Ball Nose Platform • .312"

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
–	(Geometria leggera)		–		(Geometria robusta)
–	resistenza all’usura				tenacità
–	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
M1–M2	.E..GP	KC515M	.E..GP	KC515M	–	–
M3	.E..GP	KC515M	.E..GP	KC515M	–	–
K1–K2	.E..GP	KC515M	–	–	–	–
K3	.E..GP	KC515M	–	–	–	–
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	–	–
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GP	KC515M

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
	(Geometria leggera)		Uso generico		(Geometria robusta)
	resistenza all’usura				tenacità
	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
M1–M2	.E..GP	KC515M	.E..GP	KC515M	–	–
M3	.E..GP	KC515M	.E..GP	KC515M	–	–
K1–K2	.E..GP	KC515M	–	–	–	–
K3	.E..GP	KC515M	–	–	–	–
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	–	–
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GP	KC515M

KDMB Ball Nose Platform • .375"

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
–	(Geometria leggera)		–		(Geometria robusta)
–	resistenza all’usura				tenacità
–	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
M1–M2	.E..GP	KC515M	.E..GP	KC515M	–	–
M3	.E..GP	KC515M	.E..GP	KC515M	–	–
K1–K2	.E..GP	KC515M	.E..GP	KC515M	–	–
K3	.E..GP	KC515M	.E..GP	KC515M	–	–
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	–	–
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GP	KC515M

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
	(Geometria leggera)		Uso generico		(Geometria robusta)
	resistenza all’usura				tenacità
	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
M1–M2	.E..GP	KC515M	.E..GP	KC515M	–	–
M3	.E..GP	KC515M	.E..GP	KC515M	–	–
K1–K2	.E..GP	KC515M	.E..GP	KC515M	–	–
K3	.E..GP	KC515M	.E..GP	KC515M	–	–
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	–	–
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GP	KC515M

KDMB Ball Nose Platform • .500"

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
–	(Geometria leggera)		–		(Geometria robusta)
–	resistenza all’usura				tenacità
–	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..HC	KC530M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
M1–M2	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
M3	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
K1–K2	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
K3	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	.E..HC	KC530M
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GN	KC515M

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
	(Geometria leggera)		Uso generico		(Geometria robusta)
	resistenza all’usura				tenacità
	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..HC	KC530M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
M1–M2	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
M3	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
K1–K2	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
K3	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	.E..HC	KC530M
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GN	KC515M

KDMB Ball Nose Platform • .625"

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
–	(Geometria leggera)		–		(Geometria robusta)
–	resistenza all’usura				tenacità
–	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..HC	KC530M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
M1–M2	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
M3	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
K1–K2	.E..GP	KC515M	.E..GP	KC515M	–	–
K3	.E..GP	KC515M	.E..GP	KC515M	–	–
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	.E..HC	KC530M
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GP	KC515M

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
	(Geometria leggera)		Uso generico		(Geometria robusta)
	resistenza all’usura				tenacità
	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..HC	KC530M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
M1–M2	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
M3	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
K1–K2	.E..GP	KC515M	.E..GP	KC515M	–	–
K3	.E..GP	KC515M	.E..GP	KC515M	–	–
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	.E..HC	KC530M
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GP	KC515M

KDMB Ball Nose Platform • .750"

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
–	(Geometria leggera)		–		(Geometria robusta)
–	resistenza all’usura				tenacità
–	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..HC	KC530M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
M1–M2	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
M3	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
K1–K2	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
K3	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	.E..HC	KC530M
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GN	KC515M

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
	(Geometria leggera)		Uso generico		(Geometria robusta)
	resistenza all’usura				tenacità
	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..HC	KC530M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
M1–M2	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
M3	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
K1–K2	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
K3	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	.E..HC	KC530M
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GN	KC515M

KDMB Ball Nose Platform • 1.00"

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
–	(Geometria leggera)		–		(Geometria robusta)
–	resistenza all’usura				tenacità
–	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..HC	KC530M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
M1–M2	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
M3	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
K1–K2	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
K3	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	.E..HC	KC530M
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GN	KC515M

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
	(Geometria leggera)		Uso generico		(Geometria robusta)
	resistenza all’usura				tenacità
	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..HC	KC530M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..HC	KC530M
M1–M2	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
M3	.E..GP	KC515M	.E..HC	KC530M	.E..HC	KC530M
K1–K2	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
K3	.E..GP	KC515M	.E..GN	KC515M	.E..GN	KC515M
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M	.E..HC	KC530M
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GN	KC515M

KDMB Ball Nose Platform • 1.25"

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
–	(Geometria leggera)		–		(Geometria robusta)
–	resistenza all’usura				tenacità
–	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
M1–M2	.E..GP	KC515M	.E..GP	KC515M	–	–
M3	.E..GP	KC515M	.E..GP	KC515M	–	–
K1–K2	.E..GP	KC515M	–	–	–	–
K3	.E..GP	KC515M	–	–	–	–
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GP	KC515M

Gruppo materiali	Lavorazione leggera		Uso generico		Lavorazione pesante
	(Geometria leggera)		Uso generico		(Geometria robusta)
	resistenza all’usura				tenacità
	Geometria	Qualità	Geometria	Qualità	Geometria	Qualità
P1–P2	.E..GP	KC515M	.E..GP	KC515M	.E..GP	KC515M
P3–P4	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
P5–P6	.E..GP	KC505M	.E..GP	KC515M	.E..GP	KC515M
M1–M2	.E..GP	KC515M	.E..GP	KC515M	–	–
M3	.E..GP	KC515M	.E..GP	KC515M	–	–
K1–K2	.E..GP	KC515M	–	–	–	–
K3	.E..GP	KC515M	–	–	–	–
N1–N2	.E..LD	K115M	.E..LD	K115M	–	–
N3	.E..LD	K115M	.E..LD	K115M	–	–
S1–S2	–	–	–	–	–	–
S3	–	–	–	–	–	–
S4	.E..LD	K115M	.E..GP	KC515M
H1	.E..GP	KC505M	.E..GP	KC505M	.E..GP	KC515M

Ulteriori informazioniView Less

You are about to leave the Solution building process.

Are you sure you want to leave?

Material Number	2878446
ISO Catalog ID	KDMB0500R630A050ST
ANSI Catalog ID	KDMB0500R630A050ST
[D1] Diametro di taglio effettivo	12.7 mm
[D1] Diametro di taglio effettivo	0.5 in
[D] Dia adattatore / stelo / foro	15.875 mm
[D] Dia adattatore / stelo / foro	0.625 in
[L] Lunghezza complessiva	160 mm
[L] Lunghezza complessiva	6.3 in
[L2] Lunghezza testa	60 mm
[L2] Lunghezza testa	2.36 in
[AP1MAX] 1° profondità di taglio massima	6.35 mm
[AP1MAX] 1° profondità di taglio massima	0.25 in
Numero di inserti	1
[Z] Numero di vani	2
Massimo angolo di rampa	3
Max giri/min	40000
Inserto di riferimento	KDMB0500.
Peso in libbre	0.47

Suggerimenti sui prodotti

Product Family suggestions

Messaggio al Team vendite

Notifications

Messaggio al Team vendite

Prodotto simile a :

KDMB™ • End Mill • Cylindrical Shank • Steel • Tapered • Inch

Indexable Ball Nose Finisher

Material Number2878446

ISO Catalog IDKDMB0500R630A050STANSI Catalog IDKDMB0500R630A050ST

Sending to {{cadTool}} in progress...

Materiale da lavorare

Uses and application

Features and benefits

Feeds

KDMB Ball Nose • .250"

At .125 Axial Depth of Cut (ap)

At .050 Axial Depth of Cut (ap)

At .025 Axial Depth of Cut (ap)

At .013 Axial Depth of Cut (ap)

KDMB Ball Nose • .312"

At .156 Axial Depth of Cut (ap)

At .047 Axial Depth of Cut (ap)

At .031 Axial Depth of Cut (ap)

At .016 Axial Depth of Cut (ap)

KDMB Ball Nose • .375"

At .188 Axial Depth of Cut (ap)

At .056 Axial Depth of Cut (ap)

At .038 Axial Depth of Cut (ap)

At .019 Axial Depth of Cut (ap)

KDMB Ball Nose • .500"

At .250 Axial Depth of Cut (ap)

At .075 Axial Depth of Cut (ap)

At .050 Axial Depth of Cut (ap)

At .025 Axial Depth of Cut (ap)

KDMB Ball Nose • .625"

At .313 Axial Depth of Cut (ap)

At .094 Axial Depth of Cut (ap)

At .063 Axial Depth of Cut (ap)

At .031 Axial Depth of Cut (ap)

KDMB Ball Nose • .750"

At .375 Axial Depth of Cut (ap)

At .113 Axial Depth of Cut (ap)

At .075 Axial Depth of Cut (ap)

At .038 Axial Depth of Cut (ap)

KDMB Ball Nose • 1.00"

At .500 Axial Depth of Cut (ap)

At .150 Axial Depth of Cut (ap)

At .100 Axial Depth of Cut (ap)

At .050 Axial Depth of Cut (ap)

KDMB Ball Nose • 1.25"

At .625 Axial Depth of Cut (ap)

At .188 Axial Depth of Cut (ap)

At .125 Axial Depth of Cut (ap)

At .063 Axial Depth of Cut (ap)

Speeds

Recommended Starting Speeds [SFM]

Insert Selection

KDMB Ball Nose Platform • .250"

KDMB Ball Nose Platform • .312"

KDMB Ball Nose Platform • .375"

KDMB Ball Nose Platform • .500"

KDMB Ball Nose Platform • .625"

KDMB Ball Nose Platform • .750"

KDMB Ball Nose Platform • 1.00"

KDMB Ball Nose Platform • 1.25"

The following files are available