Drilling
Drilling: Inclined Entry
Drilling: Inclined Exit
Drilling: X-Offset
Drilling: Convex
Shank - Cylindrical Whistle Notch with Drive and Flange
Through Coolant: Radial: Indexable Drilling
Drilling: Blind
Chain Drilling
Drilling: Cross-Hole Drilling
Drilling: Half-Cylindrical Drilling
Drilling: Corner Drilling 45°Downloaded file will be available after import in the {{cadTool}} tool library.
| Material Number | 1799056 |
| ISO Catalog ID | DFR210R3WD25M |
| ANSI Catalog ID | DFR210R3WD25M |
| [D] Adapter / Shank / Bore Diameter | 25 mm |
| [D] Adapter / Shank / Bore Diameter | .9843 in |
| [D1] Drill Diameter M | 21 mm |
| [D1] Drill Diameter M | .8268 in |
| [D1MAX] Drill Diameter Maximum | 22 mm |
| [D1MAX] Drill Diameter Maximum | .8661 in |
| [L1] Insert Gage Length | 95.552 mm |
| [L1] Insert Gage Length | 3.761 in |
| [L4] Maximum Drilling Depth | 63 mm |
| [L4] Maximum Drilling Depth | 2.48 in |
| [L5] Drill Point Length | 0.755 mm |
| [L5] Drill Point Length | .0297 in |
| [LS] Shank Length | 45 mm |
| [LS] Shank Length | 1.771 in |
| Gage Insert | DFR0403. |
DrillingDrilling: Inclined EntryDrilling: Inclined ExitDrilling: X-OffsetDrilling: ConvexShank - Cylindrical Whistle Notch with Drive and FlangeThrough Coolant: Radial: Indexable DrillingDrilling: BlindChain DrillingDrilling: Cross-Hole DrillingDrilling: Half-Cylindrical DrillingDrilling: Corner Drilling 45°Create Solution to calculate Feeds and Speeds
After creating a solution just choose the Feeds & Speeds icon and our system will provide recommendations. You can customize the information by adding your machine and specifications or make adjustments using the sliders.
| WARNING During through-hole operations, a slug or disc is produced as the tool breaks through the workpiece. When the drill is stationary and the workpiece is rotating, this slug may be hurled from the chuck by centrifugal force. Provide adequate shielding to protect bystanders. |
| D | LS |
| 20 | 45 |
| 25 | 45 |
| 32 | 58 |
| Metric | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... 12,50–16,00mm | DFR03... 16,50–20,00mm | DFR04... 20,50–24,00mm | ||||||
| P | 1 | S | O | MD | KCU25 | 310 | 325 | 360 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KCU40 | 200 | 215 | 230 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 130 | 135 | 150 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | GD | KCPK10 | 310 | 325 | 360 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 200 | 215 | 230 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 130 | 135 | 150 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| 3 | S | O | GD | KCPK10 | 260 | 285 | 320 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 180 | 195 | 220 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 110 | 120 | 140 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| 4 | S | O | GD | KCU25 | 220 | 250 | 300 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 150 | 180 | 220 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 90 | 110 | 140 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| 5 | S | O | GD | KCU25 | 180 | 200 | 220 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 120 | 135 | 150 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 70 | 85 | 100 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | ||
| I | LD | KC7140 | ||||||||||
| 6 | S | O | GD | KCU25 | 180 | 200 | 220 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 120 | 135 | 150 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 70 | 85 | 100 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | ||
| I | LD | KC7140 | ||||||||||
| M | 1 | S | O | MD | KC7140 | 150 | 190 | 230 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 60 | 80 | 100 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | MD | KC7140 | 150 | 180 | 210 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 60 | 80 | 100 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | ||
| I | MD | KC7140 | ||||||||||
| 3 | S | O | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 80 | 110 | 140 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 50 | 70 | 90 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | ||
| I | MD | KC7140 | ||||||||||
| Metric | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... 12,50–16,00mm | DFR03... 16,50–20,00mm | DFR04... 20,50–24,00mm | |
| P | 1 | S | O | MD | KCU25 | 310 | 325 | 360 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 |
| 1 | S | I | MD | KC7140 | 310 | 325 | 360 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 1 | U | O | MD | KCU40 | 200 | 215 | 230 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 1 | U | I | MD | KC7140 | 200 | 215 | 230 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 1 | I | O | MD | KC7140 | 130 | 135 | 150 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 1 | I | I | MD | KC7140 | 130 | 135 | 150 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 2 | S | O | GD | KCPK10 | 310 | 325 | 360 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 2 | S | I | LD | KC7140 | 310 | 325 | 360 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 2 | U | O | GD | KCU40 | 200 | 215 | 230 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 2 | U | I | LD | KC7140 | 200 | 215 | 230 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 2 | I | O | MD | KC7140 | 130 | 135 | 150 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 2 | I | I | LD | KC7140 | 130 | 135 | 150 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 3 | S | O | GD | KCPK10 | 260 | 285 | 320 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 3 | S | I | LD | KC7140 | 260 | 285 | 320 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 3 | U | O | GD | KCU40 | 180 | 195 | 220 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 3 | U | I | LD | KC7140 | 180 | 195 | 220 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 3 | I | O | GD | KC7140 | 110 | 120 | 140 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 3 | I | I | LD | KC7140 | 110 | 120 | 140 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 4 | S | O | GD | KCU25 | 220 | 250 | 300 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 4 | S | I | LD | KC7140 | 220 | 250 | 300 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 4 | U | O | GD | KCU40 | 150 | 180 | 220 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 4 | U | I | LD | KC7140 | 150 | 180 | 220 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 4 | I | O | GD | KC7140 | 90 | 110 | 140 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 4 | I | I | LD | KC7140 | 90 | 110 | 140 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| 5 | S | O | GD | KCU25 | 180 | 200 | 220 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 5 | S | I | LD | KC7140 | 180 | 200 | 220 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 5 | U | O | GD | KCU40 | 120 | 135 | 150 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 5 | U | I | LD | KC7140 | 120 | 135 | 150 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 5 | I | O | GD | KC7140 | 70 | 85 | 100 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 5 | I | I | LD | KC7140 | 70 | 85 | 100 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 6 | S | O | GD | KCU25 | 180 | 200 | 220 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 6 | S | I | LD | KC7140 | 180 | 200 | 220 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 6 | U | O | GD | KCU40 | 120 | 135 | 150 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 6 | U | I | LD | KC7140 | 120 | 135 | 150 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 6 | I | O | GD | KC7140 | 70 | 85 | 100 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| 6 | I | I | LD | KC7140 | 70 | 85 | 100 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| Metric | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... 12,50–16,00 | DFR03... 16,50–20,00 | DFR04... 20,50–24,00 | ||||||
| P | 1 | S | O | MD | KCU25 | 310 | 325 | 360 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KCU40 | 200 | 215 | 230 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 130 | 135 | 150 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | GD | KCPK10 | 310 | 325 | 360 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 200 | 215 | 230 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 130 | 135 | 150 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| 3 | S | O | GD | KCPK10 | 260 | 285 | 320 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 180 | 195 | 220 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 110 | 120 | 140 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| 4 | S | O | GD | KCU25 | 220 | 250 | 300 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 150 | 180 | 220 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 90 | 110 | 140 | mm/r | 0,09–0,15 | 0,11–0,18 | 0,15–0,25 | ||
| I | LD | KC7140 | ||||||||||
| 5 | S | O | GD | KCU25 | 180 | 200 | 220 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 120 | 135 | 150 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 70 | 85 | 100 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | ||
| I | LD | KC7140 | ||||||||||
| 6 | S | O | GD | KCU25 | 180 | 200 | 220 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 120 | 135 | 150 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 70 | 85 | 100 | mm/r | 0,07–0,13 | 0,09–0,15 | 0,11–0,18 | ||
| I | LD | KC7140 | ||||||||||
| M | 1 | S | O | MD | KC7140 | 150 | 190 | 230 | mm/r | 0,07-0,13 | 0,08-0,16 | 0,10-0,18 |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 60 | 80 | 100 | mm/r | 0,07-0,13 | 0,08-0,16 | 0,10-0,18 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | MD | KC7140 | 150 | 180 | 210 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07-0,13 | 0,08-0,16 | 0,10-0,18 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 60 | 80 | 100 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | ||
| I | MD | KC7140 | ||||||||||
| 3 | S | O | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07-0,13 | 0,08-0,16 | 0,10-0,18 | |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 80 | 110 | 140 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 50 | 70 | 90 | mm/r | 0,07-0,13 | 0,08-0,16 | 0,10-0,18 | ||
| I | MD | KC7140 | ||||||||||
| Metric | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... 12,50–16,00 | DFR03... 16,50–20,00 | DFR04... 20,50–24,00 | |
| M | 1 | S | O | MD | KC7140 | 150 | 190 | 230 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 |
| 1 | S | I | MD | KC7140 | 150 | 190 | 230 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 1 | U | O | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 1 | U | I | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 1 | I | O | MD | KC7140 | 60 | 80 | 100 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 1 | I | I | MD | KC7140 | 60 | 80 | 100 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 2 | S | O | MD | KC7140 | 150 | 180 | 210 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 2 | S | I | MD | KC7140 | 150 | 180 | 210 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 2 | U | O | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 2 | U | I | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 2 | I | O | MD | KC7140 | 60 | 80 | 100 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 2 | I | I | MD | KC7140 | 60 | 80 | 100 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 3 | S | O | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 3 | S | I | MD | KC7140 | 100 | 130 | 160 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 3 | U | O | MD | KC7140 | 80 | 110 | 140 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 3 | U | I | MD | KC7140 | 80 | 110 | 140 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 3 | I | O | MD | KC7140 | 50 | 70 | 90 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| 3 | I | I | MD | KC7140 | 50 | 70 | 90 | mm/r | 0,07–0,13 | 0,08–0,16 | 0,10–0,18 | |
| Metric | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... 12,50–16,00mm | DFR03... 16,50–20,00mm | DFR04... 20,50–24,00mm | ||||||
| K | 1 | S | O | GD | KCPK10 | 200 | 240 | 300 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 120 | 155 | 200 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 80 | 100 | 125 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| 2 | S | O | GD | KCPK10 | 180 | 220 | 260 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 110 | 140 | 170 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 80 | 100 | 120 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| 3 | S | O | GD | KCPK10 | 180 | 220 | 260 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 110 | 140 | 170 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 80 | 100 | 120 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| N | 1 | S | O | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 300 | 400 | 500 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| 2 | S | O | ST | KD1425 | 375 | 550 | 775 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 175 | 250 | 325 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| 3 | S | O | ST | KD1425 | 350 | 500 | 650 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 150 | 250 | 350 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| 4 | S | O | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| 5 | S | O | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| 6 | S | O | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| I | ST | KD1425 | ||||||||||
| U | O | GD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | GD | KCU40 | ||||||||||
| I | O | GD | KMF | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | GD | KMF | ||||||||||
| Metric | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... 12,50–16,00mm | DFR03... 16,50–20,00mm | DFR04... 20,50–24,00mm | |
| K | 1 | S | O | GD | KCPK10 | 200 | 240 | 300 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 |
| 1 | S | I | LD | KCU40 | 200 | 240 | 300 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 1 | U | O | GD | KCU25 | 120 | 155 | 200 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 1 | U | I | LD | KC7140 | 120 | 155 | 200 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 1 | I | O | GD | KCU40 | 80 | 100 | 125 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 1 | I | I | LD | KC7140 | 80 | 100 | 125 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 2 | S | O | GD | KCPK10 | 180 | 220 | 260 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 2 | S | I | LD | KCU40 | 180 | 220 | 260 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 2 | U | O | GD | KCU25 | 110 | 140 | 170 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 2 | U | I | LD | KC7140 | 110 | 140 | 170 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 2 | I | O | GD | KCU40 | 80 | 100 | 120 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 2 | I | I | LD | KC7140 | 80 | 100 | 120 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 3 | S | O | GD | KCPK10 | 180 | 220 | 260 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 3 | S | I | LD | KCU40 | 180 | 220 | 260 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 3 | U | O | GD | KCU25 | 110 | 140 | 170 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 3 | U | I | LD | KC7140 | 110 | 140 | 170 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 3 | I | O | GD | KCU40 | 80 | 100 | 120 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| 3 | I | I | LD | KC7140 | 80 | 100 | 120 | mm/tr | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| Metric | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... 12,50–16,00 | DFR03... 16,50–20,00 | DFR04... 20,50–24,00 | ||||||
| K | 1 | S | O | GD | KCPK10 | 200 | 240 | 300 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 120 | 155 | 200 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 80 | 100 | 125 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| 2 | S | O | GD | KCPK10 | 180 | 220 | 260 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 110 | 140 | 170 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 80 | 100 | 120 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| 3 | S | O | GD | KCPK10 | 180 | 220 | 260 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 110 | 140 | 170 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 80 | 100 | 120 | mm/r | 0,10–0,18 | 0,12–0,20 | 0,14–0,24 | ||
| I | LD | KC7140 | ||||||||||
| N | 1 | S | O | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07-0,09 | 0,10-0,14 | 0,12-0,16 |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 300 | 400 | 500 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 200 | 300 | 400 | mm/r | 0,07-0,09 | 0,10-0,14 | 0,12-0,16 | ||
| I | LD | KCU40 | ||||||||||
| 2 | S | O | ST | KD1425 | 375 | 550 | 775 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07-0,09 | 0,10-0,14 | 0,12-0,16 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 175 | 250 | 325 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| 3 | S | O | ST | KD1425 | 350 | 500 | 650 | mm/r | 0,07-0,09 | 0,10-0,14 | 0,12-0,16 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 150 | 250 | 350 | mm/r | 0,07-0,09 | 0,10-0,14 | 0,12-0,16 | ||
| I | LD | KCU40 | ||||||||||
| 4 | S | O | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07-0,09 | 0,10-0,14 | 0,12-0,16 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | LD | KCU40 | ||||||||||
| 6 | S | O | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07-0,09 | 0,10-0,14 | 0,12-0,16 | |
| I | ST | KD1425 | ||||||||||
| U | O | HP | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | ||
| I | HP | KCU40 | ||||||||||
| I | O | HP | KMF | 200 | 300 | 400 | mm/r | 0,07-0,09 | 0,10-0,14 | 0,12-0,16 | ||
| I | HP | KMF | ||||||||||
| Metric | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... 12,50–16,00mm | DFR03... 16,50–20,00mm | DFR04... 20,50–24,00mm | |
| N | 1 | S | O | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 |
| 1 | S | I | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 1 | U | O | LD | KCU40 | 300 | 400 | 500 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 1 | U | I | LD | KCU40 | 300 | 400 | 500 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 1 | I | O | LD | KCU40 | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 1 | I | I | LD | KCU40 | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 2 | S | O | ST | KD1425 | 375 | 550 | 775 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 2 | S | I | ST | KD1425 | 375 | 550 | 775 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 2 | U | O | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 2 | U | I | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 2 | I | O | LD | KCU40 | 175 | 250 | 325 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 2 | I | I | LD | KCU40 | 175 | 250 | 325 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 3 | S | O | ST | KD1425 | 350 | 500 | 650 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 3 | S | I | ST | KD1425 | 350 | 500 | 650 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 3 | U | O | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 3 | U | I | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 3 | I | O | LD | KCU40 | 150 | 250 | 350 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 3 | I | I | LD | KCU40 | 150 | 250 | 350 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 4 | S | O | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 4 | S | I | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 4 | U | O | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 4 | U | I | LD | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 4 | I | O | LD | KCU40 | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 4 | I | I | LD | KCU40 | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 6 | S | O | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 6 | S | I | ST | KD1425 | 400 | 600 | 800 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 6 | U | O | HP | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 6 | U | I | HP | KCU40 | 250 | 350 | 450 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 6 | I | O | HP | KMF | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| 6 | I | I | HP | KMF | 200 | 300 | 400 | mm/r | 0,07–0,09 | 0,10–0,14 | 0,12–0,16 | |
| Metric | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... 12,50 | DFR03... 16,50 | DFR04... 20,50 | ||||||
| S | 1 | S | O | GD | KCU40 | 60 | 70 | 75 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 40 | 50 | 60 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 25 | 30 | 40 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | GD | KCU40 | 50 | 60 | 70 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 30 | 40 | 50 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 25 | 30 | 40 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | ||
| I | MD | KC7140 | ||||||||||
| 3 | S | O | GD | KCU40 | 70 | 80 | 90 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 50 | 60 | 70 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 30 | 40 | 50 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | ||
| I | MD | KC7140 | ||||||||||
| 4 | S | O | GD | KCU40 | 70 | 80 | 90 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 50 | 60 | 70 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 30 | 40 | 50 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | ||
| I | MD | KC7140 | ||||||||||
| Metric | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... 12,50-16,00 mm | DFR03... 16,50-20,00 mm | DFR04... 20,50-24,00 mm | |
| S | 1 | S | O | GD | KCU40 | 60 | 70 | 75 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 |
| 1 | S | I | LD | KCU40 | 60 | 70 | 75 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 1 | U | O | GD | KCU40 | 40 | 50 | 60 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 1 | U | I | LD | KC7140 | 40 | 50 | 60 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 1 | I | O | MD | KC7140 | 25 | 30 | 40 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 1 | I | I | MD | KC7140 | 25 | 30 | 40 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 2 | S | O | GD | KCU40 | 50 | 60 | 70 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 2 | S | I | LD | KCU40 | 50 | 60 | 70 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 2 | U | O | GD | KCU40 | 30 | 40 | 50 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 2 | U | I | LD | KC7140 | 30 | 40 | 50 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 2 | I | O | MD | KC7140 | 25 | 30 | 40 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 2 | I | I | MD | KC7140 | 25 | 30 | 40 | mm/r | 0,04–0,06 | 0,05–0,08 | 0,06–0,10 | |
| 3 | S | O | GD | KCU40 | 70 | 80 | 90 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 3 | S | I | LD | KCU40 | 70 | 80 | 90 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 3 | U | O | GD | KCU40 | 50 | 60 | 70 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 3 | U | I | LD | KC7140 | 50 | 60 | 70 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 3 | I | O | MD | KC7140 | 30 | 40 | 50 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 3 | I | I | MD | KC7140 | 30 | 40 | 50 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 4 | S | O | GD | KCU40 | 70 | 80 | 90 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 4 | S | I | LD | KCU40 | 70 | 80 | 90 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 4 | U | O | GD | KCU40 | 50 | 60 | 70 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 4 | U | I | LD | KC7140 | 50 | 60 | 70 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 4 | I | O | MD | KC7140 | 30 | 40 | 50 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| 4 | I | I | MD | KC7140 | 30 | 40 | 50 | mm/r | 0,05–0,08 | 0,06–0,10 | 0,06–0,10 | |
| Metric | ||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||
| Range | ||||||||||
| Min | Starting Value | Max | Ø | DFR04 20,50–24,00mm | ||||||
| N | 1 | S | O | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 |
| I | ST | KD1425 | ||||||||
| 2 | S | O | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 3 | S | O | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 4 | S | O | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 5 | S | O | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
| I | ST | KD1425 | ||||||||
| Inch | ||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||
| Range | ||||||||||
| Min | Starting Value | Max | Ø | DFR04 .813–1.00" | ||||||
| N | 1 | S | O | ST | KD1425 | 1300 | 2362 | 2760 | IPR | .002–.003 |
| I | ST | KD1425 | ||||||||
| 2 | S | O | ST | KD1425 | 1209 | 2197 | 2567 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 3 | S | O | ST | KD1425 | 1118 | 2032 | 2374 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 4 | S | O | ST | KD1425 | 1560 | 2362 | 2760 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 5 | S | O | ST | KD1425 | 1575 | 2362 | 2834 | IPR | .002–.003 | |
| I | ST | KD1425 | ||||||||
| Metric | ||||||||||
| Cutting Speed | ||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR04 20,50–24,00 mm | |
| N | 1 | S | O | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 |
| 1 | S | I | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 | |
| 2 | S | O | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| 2 | S | I | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| 3 | S | O | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| 3 | S | I | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| 4 | S | O | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| 4 | S | I | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| 5 | S | O | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
| 5 | S | I | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
I have read and accepted the Terms & Conditions of use
ISO Catalog Number
ANSI Catalog Number
to find similar products.Please select a file to download
Models
. Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.
Minimum quantity should be
| SAP Material Number | ISO Catalog Number | Grade |
|---|
You are about to leave the Solution building process.
Are you sure you want to leave?