Face Milling
Slotting: Square End
Side Milling/Shoulder Milling: Square End
Milling - Side and FaceDownloaded file will be available after import in the {{cadTool}} tool library.
| Objednací číslo | 1229081 |
| ISO katalogové ID | KSSR400SP10T30F5 |
| ANSI katalogové ID | KSSR400SP10T30F5 |
| [D1] Effective Cutting Diameter | 101.6 mm |
| [D1] Effective Cutting Diameter | 4 in |
| [D] Adapter / Shank / Bore Diameter | 31.75 mm |
| [D] Adapter / Shank / Bore Diameter | 1.25 in |
| [D6] Hub Diameter | 73.025 mm |
| [D6] Hub Diameter | 2.875 in |
| [L] Overall Length | 50.8 mm |
| [L] Overall Length | 2 in |
| [AP1MAX] 1st Maximum Cutting Depth | 6.57 mm |
| [AP1MAX] 1st Maximum Cutting Depth | .2587 in |
| Number of Inserts | 10 |
| Weight Pounds | 3.88 |
| Max RPM | 18600 |
Face MillingSlotting: Square EndSide Milling/Shoulder Milling: Square EndMilling - Side and FaceVytvořit řešení pro výpočet posuvů a rychlosti
Po vytvoření řešení stačí vybrat ikonu Posuvy & Rychlosti a náš systém poskytne doporučení. Informace můžete upravit přidáním zařízení a specifikací nebo provést úpravy pomocí posuvníků.
| KSSM™ 10 • Recommended Starting Feeds [mm/th] | |||||||||||||||
| Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | ||||||||||||||
| 5% | 10% | 20% | 30% | 40–100% | |||||||||||
| L | M | H | L | M | H | L | M | H | L | M | H | L | M | H | |
| .F..LE | 0,12 | 0,42 | 0,70 | 0,08 | 0,30 | 0,50 | 0,06 | 0,23 | 0,38 | 0,06 | 0,20 | 0,33 | 0,05 | 0,18 | 0,30 |
| .E..LD2 | 0,12 | 0,46 | 0,81 | 0,09 | 0,33 | 0,58 | 0,07 | 0,25 | 0,43 | 0,06 | 0,22 | 0,38 | 0,05 | 0,20 | 0,35 |
| .E..GB2 | 0,23 | 0,53 | 0,89 | 0,17 | 0,38 | 0,64 | 0,13 | 0,29 | 0,48 | 0,11 | 0,25 | 0,41 | 0,10 | 0,23 | 0,38 |
| .S..GB2 | 0,23 | 0,59 | 0,95 | 0,17 | 0,43 | 0,68 | 0,13 | 0,32 | 0,51 | 0,11 | 0,28 | 0,44 | 0,10 | 0,25 | 0,41 |
| L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use Light Machining values as starting feed rate. | |||||||||||||||
| KSSM™ 10 • Recommended Starting Feeds [IPT] | |||||||||||||||
| Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | ||||||||||||||
| 5% | 10% | 20% | 30% | 40–100% | |||||||||||
| L | M | H | L | M | H | L | M | H | L | M | H | L | M | H | |
| .F..LE | 0.005 | 0.017 | 0.028 | 0.003 | 0.012 | 0.020 | 0.003 | 0.009 | 0.015 | 0.002 | 0.008 | 0.013 | 0.002 | 0.007 | 0.012 |
| .E..LD2 | 0.005 | 0.018 | 0.032 | 0.004 | 0.013 | 0.023 | 0.003 | 0.010 | 0.017 | 0.002 | 0.009 | 0.015 | 0.002 | 0.008 | 0.014 |
| .E..GB2 | 0.009 | 0.021 | 0.035 | 0.007 | 0.015 | 0.025 | 0.005 | 0.011 | 0.019 | 0.004 | 0.010 | 0.016 | 0.004 | 0.009 | 0.015 |
| .S..GB2 | 0.009 | 0.023 | 0.037 | 0.007 | 0.017 | 0.027 | 0.005 | 0.013 | 0.020 | 0.004 | 0.011 | 0.017 | 0.004 | 0.010 | 0.016 |
| L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use Light Machining values as starting feed rate. | |||||||||||||||
| KSSM™ 10 • Recommended Starting Speed [m/min] | |||||||||||||||||||||||||
| Sorta | KCPM20 | KC410M | KC725M | KCK15 | KCPK30 | KCK20B | KCPM40 | KTPK20 | |||||||||||||||||
| Tloušťka třísky hex mm | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | |||||||||
| Materiálová skupina | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | |
| P | 1 | 550 | 485 | 450 | – | – | – | 260 | 230 | 215 | – | – | – | 455 | 395 | 370 | – | – | – | 295 | 260 | 245 | 365 | 300 | 255 |
| 2 | 340 | 310 | 275 | – | – | – | 220 | 190 | 160 | – | – | – | 280 | 255 | 230 | – | – | – | 250 | 215 | 180 | 265 | 220 | 200 | |
| 3 | 310 | 275 | 255 | – | – | – | 200 | 170 | 140 | – | – | – | 255 | 230 | 205 | – | – | – | 230 | 195 | 160 | 245 | 200 | 180 | |
| 4 | 230 | 215 | 190 | – | – | – | 180 | 150 | 120 | – | – | – | 225 | 185 | 160 | – | – | – | 205 | 170 | 135 | 210 | 180 | 160 | |
| 5 | 275 | 250 | 230 | – | – | – | 150 | 135 | 120 | – | – | – | 190 | 170 | 150 | – | – | – | 170 | 155 | 135 | 185 | 170 | 150 | |
| 6 | 190 | 170 | 145 | – | – | – | 130 | 100 | 80 | – | – | – | 160 | 135 | 110 | – | – | – | 150 | 115 | 90 | 160 | 130 | 100 | |
| M | 1 | 225 | 200 | 175 | – | – | – | 170 | 150 | 135 | – | – | – | 205 | 185 | 155 | – | – | – | 195 | 170 | 155 | 240 | 195 | 165 |
| 2 | 205 | 175 | 160 | – | – | – | 155 | 130 | 110 | – | – | – | 185 | 160 | 140 | – | – | – | 175 | 150 | 125 | 215 | 185 | 150 | |
| 3 | 160 | 145 | 125 | – | – | – | 115 | 100 | 80 | – | – | – | 145 | 130 | 115 | – | – | – | 130 | 115 | 90 | 160 | 135 | 110 | |
| K | 1 | 360 | 325 | 295 | – | – | – | – | – | – | 420 | 385 | 340 | 295 | 265 | 240 | 360 | 290 | 245 | – | – | – | 230 | 195 | 160 |
| 2 | 285 | 255 | 235 | – | – | – | – | – | – | 335 | 295 | 275 | 235 | 210 | 190 | 280 | 230 | 195 | – | – | – | 185 | 150 | 130 | |
| 3 | 240 | 215 | 200 | – | – | – | – | – | – | 280 | 250 | 230 | 195 | 175 | 160 | 210 | 175 | 140 | – | – | – | 150 | 130 | 105 | |
| N | 1 | – | – | – | 1215 | 1080 | 995 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| 2 | – | – | – | 1080 | 995 | 915 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| 3 | – | – | – | 1080 | 995 | 915 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| S | 1 | – | – | – | – | – | – | 35 | 30 | 25 | – | – | – | – | – | – | – | – | – | 40 | 35 | 30 | – | – | – |
| 2 | – | – | – | – | – | – | 35 | 30 | 25 | – | – | – | – | – | – | – | – | – | 40 | 35 | 30 | – | – | – | |
| 3 | – | – | – | – | – | – | 45 | 35 | 25 | – | – | – | – | – | – | – | – | – | 50 | 40 | 30 | – | – | – | |
| 4 | – | – | – | – | – | – | 50 | 45 | 30 | – | – | – | 50 | 45 | 35 | – | – | – | 55 | 50 | 35 | – | – | – | |
| H | 1 | 140 | 115 | 95 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. | |||||||||||||||||||||||||
| KSSM™ 10 • Recommended Starting Speed [SFM] | |||||||||||||||||||||||||
| Sorta | KCPM20 | KC410M | KC725M | KCK15 | KCPK30 | KCK20B | KCPM40 | KTPK20 | |||||||||||||||||
| Chip Thickness hex Inch | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | |||||||||
| Materiálová skupina | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | |
| P | 1 | 1805 | 1590 | 1475 | – | – | – | 855 | 755 | 705 | – | – | – | 1495 | 1295 | 1215 | – | – | – | 970 | 855 | 805 | 1200 | 985 | 835 |
| 2 | 1115 | 1015 | 900 | – | – | – | 720 | 625 | 525 | – | – | – | 920 | 835 | 755 | – | – | – | 820 | 705 | 590 | 870 | 720 | 655 | |
| 3 | 1015 | 900 | 835 | – | – | – | 655 | 560 | 460 | – | – | – | 835 | 755 | 675 | – | – | – | 755 | 640 | 525 | 805 | 655 | 590 | |
| 4 | 755 | 705 | 625 | – | – | – | 590 | 490 | 395 | – | – | – | 740 | 605 | 525 | – | – | – | 675 | 560 | 445 | 690 | 590 | 525 | |
| 5 | 900 | 820 | 755 | – | – | – | 490 | 445 | 395 | – | – | – | 625 | 560 | 490 | – | – | – | 560 | 510 | 445 | 605 | 560 | 490 | |
| 6 | 625 | 560 | 475 | – | – | – | 425 | 330 | 260 | – | – | – | 525 | 445 | 360 | – | – | – | 490 | 375 | 295 | 525 | 425 | 330 | |
| M | 1 | 740 | 655 | 575 | – | – | – | 560 | 490 | 445 | – | – | – | 675 | 605 | 510 | – | – | – | 640 | 560 | 510 | 785 | 640 | 540 |
| 2 | 670 | 575 | 525 | – | – | – | 510 | 425 | 360 | – | – | – | 605 | 525 | 460 | – | – | – | 575 | 490 | 410 | 705 | 605 | 490 | |
| 3 | 525 | 475 | 410 | – | – | – | 375 | 330 | 260 | – | – | – | 475 | 425 | 375 | – | – | – | 425 | 375 | 295 | 525 | 445 | 360 | |
| K | 1 | 1180 | 1065 | 970 | – | – | – | – | – | – | 1380 | 1265 | 1115 | 970 | 870 | 785 | 1180 | 950 | 805 | – | – | – | 755 | 640 | 525 |
| 2 | 935 | 835 | 770 | – | – | – | – | – | – | 1100 | 970 | 900 | 770 | 690 | 625 | 920 | 755 | 640 | – | – | – | 605 | 490 | 425 | |
| 3 | 785 | 705 | 655 | – | – | – | – | – | – | 920 | 820 | 755 | 640 | 575 | 525 | 690 | 575 | 460 | – | – | – | 490 | 425 | 345 | |
| N | 1 | – | – | – | 3985 | 3545 | 3265 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| 2 | – | – | – | 3545 | 3265 | 3000 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| 3 | – | – | – | 3545 | 3265 | 3000 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| S | 1 | – | – | – | – | – | – | 115 | 100 | 80 | – | – | – | – | – | – | – | – | – | 130 | 115 | 100 | – | – | – |
| 2 | – | – | – | – | – | – | 115 | 100 | 80 | – | – | – | – | – | – | – | – | – | 130 | 115 | 100 | – | – | – | |
| 3 | – | – | – | – | – | – | 150 | 115 | 80 | – | – | – | – | – | – | – | – | – | 165 | 130 | 100 | – | – | – | |
| 4 | – | – | – | – | – | – | 165 | 150 | 100 | – | – | – | 165 | 150 | 115 | – | – | – | 180 | 165 | 115 | – | – | – | |
| H | 1 | 460 | 375 | 310 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. | |||||||||||||||||||||||||
| KSSM™ 10 • Insert Selection Guide | ||||||
| Materiálová skupina | Lehké obrábění | Všeobecné použití | Těžké obrábění | |||
| – | (Lehká geometrie) | – | (Silná geometrie) | |||
| – | Odolnost proti opotřebení |  | Houževnatost | |||
| – | Geometrie | Sorta | Geometrie | Sorta | Geometrie | Sorta |
| P1–P2 | .E..GE | KCPM40 | .S..GE | KCPM40 | .S..GEM | KCPM40 |
| P3–P4 | .E..GE | KCPM40 | .S..GE | KCPK30 | .S..GEM | KCPK30 |
| P5–P6 | .E..GE | KC725M | .S..GE | KC725M | .S..GEM | KCPK30 |
| M1–M2 | .E..GE | KCSM40 | .S..GE | KCSM40 | .S..GEM | KCPM40 |
| M3 | .E..GE | KCPM40 | .S..GE | KCPM40 | .S..GEM | KCPM40 |
| K1–K2 | .S..GE | KCK20B | .S..GE | KCK15 | .S..GEM | KCK20B |
| K3 | .S..GE | KCK20B | .S..GE | KCK15 | .S..GEM | KCK20B |
| N1–N2 | .E..GEJ | KC422M | .E..GEJ | KC422M | .E..GEJ | KC422M |
| N3 | .E..GEJ | KC422M | .E..GEJ | KC422M | .E..GEJ | KC422M |
| S1–S2 | .E..GE | KC725M | .S..GE | KC725M | .S..GE | KC725M |
| S3 | .E..GE | KCSM40 | .S..GE | KCSM40 | .S..GE | KCSM40 |
| S4 | .E..GE | KCSM40 | .S..GE | KCSM40 | .S..GE | KCSM40 |
| H1 | – | – | – | – | – | – |
CAD Drawings Models
Can’t find the file type you’re looking for?
Product data
I have read and accepted the Terms & Conditions of use
Katalogové číslo ISO
Katalogové číslo ANSI
to find similar products.Please select a file to download
Models
. Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.
Minimum quantity should be
| SAP Material Number | Katalogové číslo ISO | Karbid |
|---|
You are about to leave the Solution building process.
Are you sure you want to leave?