牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
DFR 3xD Flanged Shk Holemaking - 2036665 - Kennametal
DFR Flanged Shank • 3 x D
Drill Fix™ DFR™ Drill Bodies
物料号2036665
公制样本编号DFR0656R3SSF100英制样本编号DFR0656R3SSF100
牌价
$546.31/每个
折扣
您的价格
/每个
有库存这个产品不再供应较长交货期
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
- P 钢
- M 不锈钢
- K 铸铁
- N 非铁材质
- S 高温合金
钻孔
钻孔： 斜切进刀
钻孔： 斜退刀
钻孔： X－偏移
钻孔： 凸面
刀柄 — 圆柱 哨形凹槽 带有驱动和凸缘
贯通式冷却： 径向： 可转位钻孔
钻孔： 盲孔
Chain Drilling
Drilling: Cross-Hole Drilling
Drilling: Half-Cylindrical Drilling
Drilling: Corner Drilling 45°
Sending to {{cadTool}} in progress...
Downloaded file will be available after import in the {{cadTool}} tool library.
MetricInch
| 物料号 | 2036665 |
| 公制样本编号 | DFR0656R3SSF100 |
| 英制样本编号 | DFR0656R3SSF100 |
| [D]适配接头/刀柄/镗孔直径 | 25.4 mm |
| [D]适配接头/刀柄/镗孔直径 | 1 in |
| [D1] 钻头直径 M | 16.662 mm |
| [D1] 钻头直径 M | .656 in |
| [D1MAX] 最大钻头直径 | 17.663 mm |
| [D1MAX] 最大钻头直径 | .6954 in |
| [L1] 刀片量规长度 | 74.247 mm |
| [L1] 刀片量规长度 | 2.923 in |
| [L4] 最大钻孔深度 | 49.987 mm |
| [L4] 最大钻孔深度 | 1.968 in |
| [L5] 钻尖长度 | 0.618 mm |
| [L5] 钻尖长度 | .0243 in |
| [LS] 刀柄长度 | 76.2 mm |
| [LS] 刀柄长度 | 3 in |
| Gage 刀片 | DFR0302. |
工件材料
- 钢
- 不锈钢
- 铸铁
- 非铁材质
- 高温合金
Uses and application
Features and benefits
- Drill Fix DFR with rectangular-shaped inserts offer highest stability and feed rates at smaller sizes.
- X-offset design to adjust diameter size on turning machines and optimize tolerances on machining centers.
- Drill shipped with insert screws, side pipe plug, and Torx wrench.
通过创建解决方案计算速度和进给
创建解决方案后，只需选择进给和速度图标，我们的系统将提供建议。您可以通过添加您的机床和参数来定制信息，或者使用滑块进行调整。
Warning
警告 • Drill Fix DFR
| WARNING During through-hole operations, a slug or disc is produced as the tool breaks through the workpiece. When the drill is stationary and the workpiece is rotating, this slug may be hurled from the chuck by centrifugal force. Provide adequate shielding to protect bystanders. |
阅读全文View Less
Dimension
Dimensions • DFR Flanged Shank
| D | LS |
| 20 | 50 |
阅读全文View Less
应用数据
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500–.625" | DFR03... .688–.750" | DFR04... .813–1.00" | ||||||
| P | 1 | S | O | MD | KCU25 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | GD | KCPK10 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| 3 | S | O | GD | KCPK10 | 853 | 935 | 1050 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 590 | 640 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 361 | 394 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| 4 | S | O | GD | KCU25 | 722 | 820 | 984 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 492 | 590 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 295 | 361 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| 5 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .003–.005 | .004–.006 | .004–.007 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .003–.005 | .004–.006 | .004–.007 | ||
| I | LD | KC7140 | ||||||||||
| 6 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| P | 1 | S | O | MD | KCU25 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 |
| 1 | S | I | MD | KC7140 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | U | O | MD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | U | I | MD | KC7140 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | I | I | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | S | O | GD | KCPK10 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | S | I | LD | KC7140 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | U | O | GD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | U | I | LD | KC7140 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | I | I | LD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | S | O | GD | KCPK10 | 853 | 935 | 1050 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | S | I | LD | KC7140 | 853 | 935 | 1050 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | U | O | GD | KCU40 | 590 | 640 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | U | I | LD | KC7140 | 590 | 640 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | I | O | GD | KC7140 | 361 | 394 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | I | I | LD | KC7140 | 361 | 394 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | S | O | GD | KCU25 | 722 | 820 | 984 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | S | I | LD | KC7140 | 722 | 820 | 984 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | U | O | GD | KCU40 | 492 | 590 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | U | I | LD | KC7140 | 492 | 590 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | I | O | GD | KC7140 | 295 | 361 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | I | I | LD | KC7140 | 295 | 361 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 5 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | S | I | LD | KC7140 | 590 | 656 | 722 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | U | I | LD | KC7140 | 394 | 443 | 492 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | I | I | LD | KC7140 | 230 | 279 | 328 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 6 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | S | I | LD | KC7140 | 590 | 656 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | U | I | LD | KC7140 | 394 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | I | I | LD | KC7140 | 230 | 279 | 328 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500–.625" | DFR03... .688–.750" | DFR04... .813–1.00" | ||||||
| M | 1 | S | O | MD | KC7140 | 492 | 623 | 754 | SFM | .003–.005 | .003–.006 | .004–.007 |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | MD | KC7140 | 492 | 590 | 689 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| 3 | S | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 262 | 361 | 459 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 164 | 230 | 295 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| M | 1 | S | O | MD | KC7140 | 492 | 623 | 754 | SFM | .003–.005 | .003–.006 | .004–.007 |
| 1 | S | I | MD | KC7140 | 492 | 623 | 754 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | U | I | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | I | I | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | S | O | MD | KC7140 | 492 | 590 | 689 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | S | I | MD | KC7140 | 492 | 590 | 689 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | U | I | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | I | I | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | S | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | S | I | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | U | O | MD | KC7140 | 262 | 361 | 459 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | U | I | MD | KC7140 | 262 | 361 | 459 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | I | O | MD | KC7140 | 164 | 230 | 295 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | I | I | MD | KC7140 | 164 | 230 | 295 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| Inch | ||||||||||||
| Material | Pocket Seat | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500–.625" | DFR03... .688–.750" | DFR04... .813–1.00" | ||||||
| K | 1 | S | O | GD | KCPK10 | 656 | 787 | 984 | SFM | .004–.007 | .005–.008 | .006–.009 |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 394 | 508 | 656 | SFM | .004–.007 | .005–.008 | .006–.009 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 262 | 328 | 410 | SFM | .004–.007 | .005–.008 | .005–.009 | ||
| I | LD | KC7140 | ||||||||||
| 2 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .005–.009 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .006–.009 | ||
| I | LD | KC7140 | ||||||||||
| 3 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .006–.009 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .005–.009 | ||
| I | LD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| K | 1 | S | O | GD | KCPK10 | 656 | 787 | 984 | SFM | .004–.007 | .005–.008 | .006–.009 |
| 1 | S | I | LD | KCU40 | 656 | 787 | 984 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 1 | U | O | GD | KCU25 | 394 | 508 | 656 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 1 | U | I | LD | KC7140 | 394 | 508 | 656 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 1 | I | O | GD | KCU40 | 262 | 328 | 410 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 1 | I | I | LD | KC7140 | 262 | 328 | 410 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 2 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 2 | S | I | LD | KCU40 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 2 | U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 2 | U | I | LD | KC7140 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 2 | I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 2 | I | I | LD | KC7140 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 3 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 3 | S | I | LD | KCU40 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 3 | U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 3 | U | I | LD | KC7140 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 3 | I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 3 | I | I | LD | KC7140 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | ||||||
| N | 1 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 984 | 1312 | 1640 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 2 | S | O | ST | KD1425 | 1230 | 1804 | 2542 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 574 | 820 | 1066 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 3 | S | O | ST | KD1425 | 1148 | 1640 | 2132 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 492 | 820 | 1148 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 4 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 820 | 1148 | 1486 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 5 | S | O | HP | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | HP | KD1425 | ||||||||||
| U | O | HP | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | HP | KCU40 | ||||||||||
| I | O | HP | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | HP | KCU40 | ||||||||||
| 6 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | GD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | GD | KCU40 | ||||||||||
| I | O | GD | KMF | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | GD | KMF | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| N | 1 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 |
| 1 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | U | O | LD | KCU40 | 984 | 1312 | 1640 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | U | I | LD | KCU40 | 984 | 1312 | 1640 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | I | I | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | S | O | ST | KD1425 | 1230 | 1804 | 2542 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | S | I | ST | KD1425 | 1230 | 1804 | 2542 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | U | I | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | I | O | LD | KCU40 | 574 | 820 | 1066 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | I | I | LD | KCU40 | 574 | 820 | 1066 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | S | O | ST | KD1425 | 1148 | 1640 | 2132 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | S | I | ST | KD1425 | 1148 | 1640 | 2132 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | U | I | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | I | O | LD | KCU40 | 492 | 820 | 1148 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | I | I | LD | KCU40 | 492 | 820 | 1148 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | U | O | LD | KCU40 | 820 | 1148 | 1486 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | U | I | LD | KCU40 | 820 | 1148 | 1486 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | I | I | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | S | O | HP | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | S | I | HP | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | U | O | HP | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | U | I | HP | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | I | O | HP | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | I | I | HP | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | U | I | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | I | O | LD | KMF | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | I | I | LD | KMF | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500 | DFR03... .688 | DFR04... .813 | ||||||
| S | 1 | S | O | GD | KCU40 | 197 | 230 | 246 | SFM | .002–.002 | .002–.003 | .002–.004 |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 131 | 164 | 197 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 98 | 131 | 164 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| 3 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.004 | .002–.003 | .002–.004 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| 4 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"-.625" | DFR03... .688"-.750" | DFR04... .813"-1.00" | |
| S | 1 | S | O | GD | KCU40 | 197 | 230 | 246 | SFM | .002–.002 | .002–.003 | .002–.004 |
| 1 | S | I | LD | KCU40 | 197 | 230 | 246 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | U | O | GD | KCU40 | 131 | 164 | 197 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | U | I | LD | KC7140 | 131 | 164 | 197 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | I | I | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | S | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | S | I | LD | KCU40 | 164 | 197 | 230 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | U | O | GD | KCU40 | 98 | 131 | 164 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | U | I | LD | KC7140 | 98 | 131 | 164 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | I | I | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 3 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.004 | .002–.003 | .002–.004 | |
| 3 | S | I | LD | KCU40 | 230 | 262 | 295 | SFM | .002–.004 | .002–.003 | .002–.004 | |
| 3 | U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 3 | U | I | LD | KC7140 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 3 | I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 3 | I | I | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | S | I | LD | KCU40 | 230 | 262 | 295 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | U | I | LD | KC7140 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | I | I | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
DFR™ • PCD • 英制
| Metric | ||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||
| Range | ||||||||||
| Min | Starting Value | Max | Ø | DFR04 20,50–24,00mm | ||||||
| N | 1 | S | O | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 |
| I | ST | KD1425 | ||||||||
| 2 | S | O | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 3 | S | O | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 4 | S | O | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 5 | S | O | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
| I | ST | KD1425 | ||||||||
| Inch | ||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||
| Range | ||||||||||
| Min | Starting Value | Max | Ø | DFR04 .813–1.00" | ||||||
| N | 1 | S | O | ST | KD1425 | 1300 | 2362 | 2760 | IPR | .002–.003 |
| I | ST | KD1425 | ||||||||
| 2 | S | O | ST | KD1425 | 1209 | 2197 | 2567 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 3 | S | O | ST | KD1425 | 1118 | 2032 | 2374 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 4 | S | O | ST | KD1425 | 1560 | 2362 | 2760 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 5 | S | O | ST | KD1425 | 1575 | 2362 | 2834 | IPR | .002–.003 | |
| I | ST | KD1425 | ||||||||
| Metric | ||||||||||
| Cutting Speed | ||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR04 20,50–24,00 mm | |
| N | 1 | S | O | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 |
| 1 | S | I | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 | |
| 2 | S | O | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| 2 | S | I | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| 3 | S | O | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| 3 | S | I | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| 4 | S | O | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| 4 | S | I | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| 5 | S | O | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
| 5 | S | I | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
阅读全文View Less
I have read and accepted the Terms & Conditions of use
通过创建解决方案为您找到合适的兼容部件
产品名称
物料号
公制样本编号
英制样本编号
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
通过创建解决方案为您找到合适的兼容部件
产品名称
物料号
公制样本编号
英制样本编号
材质
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
产品名称
物料号
公制样本编号
英制样本编号
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期
牌价
/每个
折扣
您的价格
/每个
出售时采用的包装 0调整以满足最小包装尺寸。
最小数量： 0调整以达到最低订单数量。
有库存这个产品不再供应较长交货期