Face Milling
Slotting: Square End
Side Milling/Shoulder Milling: Square End
Milling - Through Coolant
Milling - Side and FaceDownloaded file will be available after import in the {{cadTool}} tool library.
| Nr materiału | 5420252 |
| Nr katalogowy ISO | KSSM88D200SN3125S075Z06 |
| Nr katalogowy ANSI | KSSM88D200SN3125S075Z06 |
| [D1] Effective Cutting Diameter | 50.8 mm |
| [D1] Effective Cutting Diameter | 2 in |
| [D1MAX] Maximum Cutting Diameter | 51.44 mm |
| [D1MAX] Maximum Cutting Diameter | 2.025 in |
| [D] Adapter / Shank / Bore Diameter | 19.1 mm |
| [D] Adapter / Shank / Bore Diameter | 0.75 in |
| [D6] Hub Diameter | 44.45 mm |
| [D6] Hub Diameter | 1.75 in |
| [L] Overall Length | 44.45 mm |
| [L] Overall Length | 1.75 in |
| [AP1MAX] 1st Maximum Cutting Depth | 9.16 mm |
| [AP1MAX] 1st Maximum Cutting Depth | 0.361 in |
| Number of Inserts | 6 |
| Weight Pounds | 0.85 |
| Max RPM | 32500 |
Face MillingSlotting: Square EndSide Milling/Shoulder Milling: Square EndMilling - Through CoolantMilling - Side and FaceZłóż nowe rozwiązanie aby obliczyc parametry posuwu i prędkości
Po złóżeniu rozwiązania wybierz ikonę "Posuwy i prędkości" a system pokaże rekomendowane wartości. Możesz doprecyzować wyniki dodając maszynę i jej specyfikacje lub zmień wartości początkowe Używając suwaki.
| Zalecane wyjściowe wartości posuwu [mm] | ||||||
| Geometria płytki | Rekomendowane początkowe wartości posuwu na ząb (Fz) w relacji do % zaangażowania promieniowego (ae) | |||||
| 30% | 40–100% | |||||
| L | M | H | L | M | H | |
| .E..LD | 0,08 | 0,19 | 0,33 | 0,08 | 0,18 | 0,30 |
| .S..GD | 0,11 | 0,24 | 0,38 | 0,10 | 0,22 | 0,35 |
| UWAGA: Jako wyjściową wartość posuwu należy przyjąć wartość określoną (zalecaną) dla obróbki lekkiej. | ||||||
| KSSM8+™ • IC10 Inch • Recommended Starting Feeds [IPT] | ||||||
| Geometria płytki | Rekomendowane początkowe wartości posuwu na ząb (Fz) w relacji do % zaangażowania promieniowego (ae) | |||||
| 30% | 40–100% | |||||
| L | M | H | L | M | H | |
| .E..LD | 0.003 | 0.008 | 0.013 | 0.003 | 0.007 | 0.012 |
| .S..GD | 0.004 | 0.009 | 0.015 | 0.004 | 0.009 | 0.014 |
| L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use "Light Machining" values as starting feed rate. | ||||||
| Zalecane wyjściowe wartości prędkości skrawania [m/min.] | ||||||||||||||||
| Gatunek | KC725M | KCK15 | KCPK30 | KCK20B | KCPM40 | |||||||||||
| Grubość wióra hex mm | Min. | Maks. | Min. | Maks. | Min. | Maks. | Min. | Maks. | Min. | Maks. | ||||||
| Grupa materiałowa | Maks. | Początek | Min. | Maks. | Początek | Min. | Maks. | Początek | Min. | Maks. | Początek | Min. | Maks. | Początek | Min. | |
| P | 1 | 260 | 230 | 215 | – | – | – | 455 | 395 | 370 | – | – | – | 295 | 260 | 245 |
| 2 | 220 | 190 | 160 | – | – | – | 280 | 255 | 230 | – | – | – | 250 | 215 | 180 | |
| 3 | 200 | 170 | 140 | – | – | – | 255 | 230 | 205 | – | – | – | 230 | 195 | 160 | |
| 4 | 180 | 150 | 120 | – | – | – | 225 | 185 | 160 | – | – | – | 205 | 170 | 135 | |
| 5 | 150 | 135 | 120 | – | – | – | 190 | 170 | 150 | – | – | – | 170 | 155 | 135 | |
| 6 | 130 | 100 | 80 | – | – | – | 160 | 135 | 110 | – | – | – | 150 | 115 | 90 | |
| M | 1 | 170 | 150 | 135 | – | – | – | 205 | 185 | 155 | – | – | – | 195 | 170 | 155 |
| 2 | 155 | 130 | 110 | – | – | – | 185 | 160 | 140 | – | – | – | 175 | 150 | 125 | |
| 3 | 115 | 100 | 80 | – | – | – | 145 | 130 | 115 | – | – | – | 130 | 115 | 90 | |
| K | 1 | – | – | – | 420 | 385 | 340 | 295 | 265 | 240 | 360 | 290 | 245 | – | – | – |
| 2 | – | – | – | 335 | 295 | 275 | 235 | 210 | 190 | 280 | 230 | 195 | – | – | – | |
| 3 | – | – | – | 280 | 250 | 230 | 195 | 175 | 160 | 210 | 175 | 140 | – | – | – | |
| N | 1 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| 2 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| 3 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| S | 1 | 35 | 30 | 25 | – | – | – | – | – | – | – | – | – | 40 | 35 | 30 |
| 2 | 35 | 30 | 25 | – | – | – | – | – | – | – | – | – | 40 | 35 | 30 | |
| 3 | 45 | 35 | 25 | – | – | – | – | – | – | – | – | – | 50 | 40 | 30 | |
| 4 | 50 | 45 | 30 | – | – | – | 50 | 45 | 35 | – | – | – | 55 | 50 | 35 | |
| H | 1 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. | ||||||||||||||||
| KSSM8+™ • IC10 • Recommended Starting Speed [SFM] | ||||||||||||||||
| Gatunek | KC725M | KCK15 | KCPK30 | KCK20B | KCPM40 | |||||||||||
| Chip Thickness hex Inch | Min. | Maks. | Min. | Maks. | Min. | Maks. | Min. | Maks. | Min. | Maks. | ||||||
| Grupa materiałowa | Maks. | Początek | Min. | Maks. | Początek | Min. | Maks. | Początek | Min. | Maks. | Początek | Min. | Maks. | Początek | Min. | |
| P | 1 | 260 | 230 | 215 | – | – | – | 455 | 395 | 370 | – | – | – | 295 | 260 | 245 |
| 2 | 220 | 190 | 160 | – | – | – | 280 | 255 | 230 | – | – | – | 250 | 215 | 180 | |
| 3 | 200 | 170 | 140 | – | – | – | 255 | 230 | 205 | – | – | – | 230 | 195 | 160 | |
| 4 | 180 | 150 | 120 | – | – | – | 225 | 185 | 160 | – | – | – | 205 | 170 | 135 | |
| 5 | 150 | 135 | 120 | – | – | – | 190 | 170 | 150 | – | – | – | 170 | 155 | 135 | |
| 6 | 130 | 100 | 80 | – | – | – | 160 | 135 | 110 | – | – | – | 150 | 115 | 90 | |
| M | 1 | 170 | 150 | 135 | – | – | – | 205 | 185 | 155 | – | – | – | 195 | 170 | 155 |
| 2 | 155 | 130 | 110 | – | – | – | 185 | 160 | 140 | – | – | – | 175 | 150 | 125 | |
| 3 | 115 | 100 | 80 | – | – | – | 145 | 130 | 115 | – | – | – | 130 | 115 | 90 | |
| K | 1 | – | – | – | 420 | 385 | 340 | 295 | 265 | 240 | 360 | 290 | 245 | – | – | – |
| 2 | – | – | – | 335 | 295 | 275 | 235 | 210 | 190 | 280 | 230 | 195 | – | – | – | |
| 3 | – | – | – | 280 | 250 | 230 | 195 | 175 | 160 | 210 | 175 | 140 | – | – | – | |
| N | 1 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| 2 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| 3 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| S | 1 | 35 | 30 | 25 | – | – | – | – | – | – | – | – | – | 40 | 35 | 30 |
| 2 | 35 | 30 | 25 | – | – | – | – | – | – | – | – | – | 40 | 35 | 30 | |
| 3 | 45 | 35 | 25 | – | – | – | – | – | – | – | – | – | 50 | 40 | 30 | |
| 4 | 50 | 45 | 30 | – | – | – | 50 | 45 | 35 | – | – | – | 55 | 50 | 35 | |
| H | 1 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. | ||||||||||||||||
| KSSM8+™ • IC10 • Insert Selection Guide | ||||||
| Grupa materiałowa | Obróbka lekka | Obróbka średnia | Obróbka ciężka | |||
| (Lekka geometria) | (Zgrubna geometria) | |||||
| odporność na zużycie |  | ciągliwość | ||||
| Geometria | Gatunek | Geometria | Gatunek | Geometria | Gatunek | |
| P1–P2 | .E..LD | KC725M | .S..GD | KCPK30 | .S..GD | KCPM40 |
| P3–P4 | .E..LD | KCPK30 | .S..GD | KCPK30 | .S..GD | KCPK30 |
| P5–P6 | .E..LD | KC725M | .S..GD | KCPM40 | .S..GD | KCPM40 |
| M1–M2 | .E..LD | KC725M | .E..LD | KC725M | .S..GD | KCPM40 |
| M3 | .E..LD | KC725M | .S..GD | KCPM40 | .S..GD | KCPM40 |
| K1–K2 | .E..LD | KCK20B | .S..GD | KCK15 | .S..GD | KCK15 |
| K3 | .E..LD | KCK20B | .S..GD | KCK15 | .S..GD | KCPK30 |
| N1–N2 | – | – | – | – | – | – |
| N3 | – | – | – | – | – | – |
| S1–S2 | .E..LD | KC725M | .E..LD | KC725M | .E..LD | KC725M |
| S3 | .E..LD | KC725M | .E..LD | KC725M | .S..GD | KCPM40 |
| S4 | .E..LD | KC725M | .E..LD | KC725M | .E..LD | KC725M |
| H1 | – | – | – | – | – | – |
I have read and accepted the Terms & Conditions of use
CAD Drawings Models
Can’t find the file type you’re looking for?
Product data
Oznaczenie katalogowe ISO
Oznaczenie katalogowe ANSI
to find similar products.Please select a file to download
Models
. Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.
Minimum quantity should be
| SAP Material Number | Oznaczenie katalogowe ISO | Gatunek |
|---|
You are about to leave the Solution building process.
Are you sure you want to leave?