Spiral Circular
Slotting: Shoulder
Face Milling
Helical Milling
Ramping: Blank
Pocketing
Counter Boring
Plunge Milling: Ball Nose
Inclined Square End MillDownloaded file will be available after import in the {{cadTool}} tool library.
| Objednací číslo | 6025618 |
| ISO katalogové ID | 7792VXE16-A066Z6R |
| ANSI katalogové ID | 7792VXE16-A066Z6R |
| [D1MAX] Maximum Cutting Diameter | 66 mm |
| [D1MAX] Maximum Cutting Diameter | 2.598 in |
| [D1] Effective Cutting Diameter | 42.045 mm |
| [D1] Effective Cutting Diameter | 1.655 in |
| [D] Adapter / Shank / Bore Diameter | 27.012 mm |
| [D] Adapter / Shank / Bore Diameter | 1.063 in |
| [D6] Hub Diameter | 55 mm |
| [D6] Hub Diameter | 2.165 in |
| [L] Overall Length | 50 mm |
| [L] Overall Length | 1.968 in |
| [AP1MAX] 1st Maximum Cutting Depth | 3.501 mm |
| [AP1MAX] 1st Maximum Cutting Depth | .1378 in |
| [Z] Number of Flutes | 6 |
Spiral CircularSlotting: ShoulderFace MillingHelical MillingRamping: BlankPocketingCounter BoringPlunge Milling: Ball NoseInclined Square End MillVytvořit řešení pro výpočet posuvů a rychlosti
Po vytvoření řešení stačí vybrat ikonu Posuvy & Rychlosti a náš systém poskytne doporučení. Informace můžete upravit přidáním zařízení a specifikací nebo provést úpravy pomocí posuvníků.
| 7792 Series • IC16 • Insert Selection Guide | ||||||
| Material Group | Light | General | Heavy | |||
| – | (Light geometry) | – | (Strong geometry) | |||
| – | wear |  | toughness | |||
| – | Geometry | Grade | Geometry | Grade | Geometry | Grade |
| P1-P2 | ...M41 | KCPM40 | ...M41 | KCPM40 | ...D41 | KCPM40 |
| P3-P4 | ...M41 | KCPM40 | …D | KCPM40 | …D41 | KCPM40 |
| P5-P6 | ...M41 | KCPM40 | ...D41 | KCPM40 | ...D41 | KCPM40 |
| M1-M2 | ...M41 | KCSM40 | ...D41 | KCSM40 | ...D41 | KCSM40 |
| M3 | ...M41 | KCSM40 | ...D41 | KCSM40 | ...D41 | KCSM40 |
| K1-K2 | …D | KCK15 | …D | KCK15 | …D | KCPK30 |
| K3 | …D | KCPK30 | …D | KCPK30 | …D | KCPK30 |
| N1-N2 | – | – | – | – | – | – |
| N3 | – | – | – | – | – | – |
| S1-S2 | ...M41 | KCSM40 | ...D41 | KCSM40 | ...D41 | KCSM40 |
| S3 | KCSM40 | SP6519 | ...D41 | KCSM40 | ...D41 | KCSM40 |
| S4 | KCSM40 | SP6519 | ...D41 | KCSM40 | ...D41 | KCSM40 |
| H1 | …D | KC522M | …D | KC522M | …D | KC522M |
| 7792 Series • IC16 • Recommended Starting Feeds [mm/th] | |||||||
| Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | ||||||
| DOC | 30% | 40–100% | |||||
| (mm) | L | M | H | L | M | H | |
| .S..D | 3,5 | 0,21 | 0,52 | 0,83 | 0,19 | 0,47 | 0,76 |
| .S..D | 2,5 | 0,24 | 0,61 | 0,97 | 0,22 | 0,55 | 0,89 |
| .S..D | 2 | 0,27 | 0,67 | 1,08 | 0,25 | 0,62 | 0,99 |
| .E..D41 | 3,5 | 0,14 | 0,46 | 0,76 | 0,13 | 0,42 | 0,70 |
| .E..D41 | 2,5 | 0,17 | 0,54 | 0,89 | 0,15 | 0,49 | 0,82 |
| .E..D41 | 2 | 0,19 | 0,60 | 0,99 | 0,17 | 0,55 | 0,91 |
| .E..M41 | 2,7 | 0,14 | 0,46 | 0,76 | 0,13 | 0,42 | 0,70 |
| .E..M41 | 2 | 0,19 | 0,60 | 0,99 | 0,17 | 0,55 | 0,91 |
| L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use Light Machining values as starting feed rate. | |||||||
| 7792 Series • IC16 • Recommended Starting Feeds for Plunging [mm/th] | ||||
| Insert Geometry |  | Programmed Feed per Tooth (fz) | ||
| L | M | H | ||
| .S..D | 0,10 | 0,25 | 0,41 | |
| .E..D41 | 0,07 | 0,23 | 0,38 | |
| .E..M41 | 0,07 | 0,23 | 0,38 | |
| L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use Light Machining values as starting feed rate. | ||||
| 7792 Series • IC16 • Recommended Starting Feeds [IPT] | |||||||
| Insert Geometry | Recommended Starting Feed per Tooth (Fz) in Relation to % of Radial Engagement (ae) | ||||||
| DOC | 30% | 40–100% | |||||
| (Inch) | L | M | H | L | M | H | |
| .S..D | 0.14 | 0.008 | 0.020 | 0.032 | 0.007 | 0.019 | 0.030 |
| .S..D | 0.1 | 0.009 | 0.024 | 0.038 | 0.009 | 0.022 | 0.035 |
| .S..D | 0.08 | 0.011 | 0.026 | 0.042 | 0.010 | 0.024 | 0.039 |
| .E..D41 | 0.14 | 0.006 | 0.018 | 0.030 | 0.005 | 0.017 | 0.028 |
| .E..D41 | 0.1 | 0.007 | 0.021 | 0.036 | 0.006 | 0.019 | 0.032 |
| .E..D41 | 0.08 | 0.007 | 0.024 | 0.039 | 0.007 | 0.022 | 0.036 |
| .E..M41 | 0.107 | 0.006 | 0.018 | 0.030 | 0.005 | 0.017 | 0.028 |
| .E..M41 | 0.08 | 0.007 | 0.024 | 0.039 | 0.007 | 0.022 | 0.036 |
| L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use Light Machining values as starting feed rate. | |||||||
| 7792 Series • IC16 • Recommended Starting Feeds for Plunging [IPT] | ||||
| Insert Geometry | | Programmed Feed per Tooth (fz) | ||
| L | M | H | ||
| .S..D | 0.004 | 0.010 | 0.016 | |
| .E..D41 | 0.003 | 0.009 | 0.015 | |
| .E..M41 | 0.003 | 0.009 | 0.015 | |
| L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use Light Machining values as starting feed rate. | ||||
| 7792 Series IC16 • Recommended Starting Speed [m/min] | |||||||||||||||||||||||||
| Grade | KC522M | KCPK30 | KCPM40 | KCSM40 | SC6525 | SP6519 | X400 | X500 | |||||||||||||||||
| Chip Thickness hex mm | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | |||||||||
| Material Group | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | |
| P | 1 | 330 | 285 | 270 | 455 | 395 | 370 | 295 | 260 | 245 | 350 | 320 | 300 | 371 | 254 | 142 | 295 | 215 | 130 | 260 | 190 | 120 | 270 | 200 | 130 |
| 2 | 275 | 240 | 200 | 280 | 255 | 230 | 250 | 215 | 180 | 300 | 270 | 220 | 325 | 225 | 121 | 260 | 190 | 115 | 230 | 170 | 105 | 240 | 280 | 115 | |
| 3 | 255 | 215 | 175 | 255 | 230 | 205 | 230 | 195 | 160 | 280 | 240 | 195 | 292 | 200 | 104 | 230 | 165 | 100 | 200 | 150 | 95 | 210 | 155 | 100 | |
| 4 | 225 | 185 | 150 | 225 | 185 | 160 | 205 | 170 | 135 | 240 | 205 | 165 | 208 | 145 | 79 | 175 | 125 | 75 | 150 | 110 | 70 | 160 | 120 | 75 | |
| 5 | 185 | 170 | 150 | 190 | 170 | 150 | 170 | 155 | 135 | 200 | 180 | 160 | 158 | 120 | 79 | 140 | 105 | 70 | – | – | – | 130 | 100 | 70 | |
| 6 | 165 | 125 | 100 | 160 | 135 | 110 | 150 | 115 | 90 | 180 | 140 | 100 | 142 | 100 | 58 | 120 | 85 | 50 | – | – | – | 110 | 80 | 50 | |
| M | 1 | 205 | 180 | 165 | 205 | 185 | 155 | 195 | 170 | 155 | 260 | 210 | 185 | 192 | 154 | 121 | 270 | 195 | 115 | – | – | – | 250 | 185 | 115 |
| 2 | 185 | 160 | 130 | 185 | 160 | 140 | 175 | 150 | 125 | 235 | 180 | 145 | 258 | 183 | 108 | 235 | 170 | 105 | – | – | – | 220 | 160 | 100 | |
| 3 | 140 | 120 | 95 | 145 | 130 | 115 | 130 | 115 | 90 | 175 | 145 | 110 | 208 | 150 | 92 | 195 | 140 | 85 | – | – | – | 180 | 130 | 80 | |
| K | 1 | 230 | 205 | 185 | 295 | 265 | 240 | – | – | – | – | – | – | 392 | 271 | 146 | – | – | – | – | – | – | – | – | – |
| 2 | 180 | 160 | 150 | 235 | 210 | 190 | – | – | – | – | – | – | 304 | 208 | 117 | – | – | – | – | – | – | – | – | – | |
| 3 | 150 | 135 | 120 | 195 | 175 | 160 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| N | 1 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| 2 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| 3 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| S | 1 | 40 | 35 | 25 | – | – | – | 40 | 35 | 30 | 50 | 40 | 25 | – | – | – | 55 | 40 | 20 | – | – | – | 45 | 35 | 25 |
| 2 | 40 | 35 | 25 | – | – | – | 40 | 35 | 30 | 55 | 40 | 25 | – | – | – | 45 | 35 | 20 | – | – | – | 45 | 30 | 20 | |
| 3 | 50 | 40 | 25 | – | – | – | 50 | 40 | 30 | 65 | 45 | 30 | – | – | – | 55 | 40 | 25 | – | – | – | 50 | 40 | 25 | |
| 4 | 50 | 45 | 35 | 50 | 45 | 35 | 55 | 50 | 35 | 75 | 60 | 40 | – | – | – | 80 | 55 | 35 | – | – | – | 60 | 50 | 35 | |
| H | 1 | 120 | 90 | 70 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | 95 | 70 | 45 | – | – | – |
| 2 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | 80 | 60 | 35 | – | – | – | |
| Recommended Starting Speed are pointing to 90° Shoulder Milling . Starting Speed for Face and Copy Milling can be Increased by 20 %. As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. | |||||||||||||||||||||||||
| 7792 Series IC16 • Recommended Starting Speed [SFM] | |||||||||||||||||||||||||
| Grade | KC522M | KCPK30 | KCPM40 | KCSM40 | SC6525 | SP6519 | X400 | X500 | |||||||||||||||||
| Chip Thickness hex Inch | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | Min | Max | |||||||||
| Material Group | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | Max | Start | Min | |
| P | 1 | 1085 | 935 | 885 | 1495 | 1295 | 1215 | 970 | 855 | 805 | 1150 | 1050 | 985 | 1217 | 833 | 458 | 970 | 705 | 425 | 855 | 625 | 395 | 885 | 655 | 425 |
| 2 | 900 | 785 | 655 | 920 | 835 | 755 | 820 | 705 | 590 | 985 | 885 | 720 | 1067 | 742 | 396 | 855 | 625 | 375 | 755 | 560 | 345 | 785 | 920 | 375 | |
| 3 | 835 | 705 | 575 | 835 | 755 | 675 | 755 | 640 | 525 | 920 | 785 | 640 | 950 | 654 | 346 | 755 | 540 | 330 | 655 | 490 | 310 | 690 | 510 | 330 | |
| 4 | 740 | 605 | 490 | 740 | 605 | 525 | 675 | 560 | 445 | 785 | 675 | 540 | 692 | 475 | 258 | 575 | 410 | 245 | 490 | 360 | 230 | 525 | 395 | 245 | |
| 5 | 605 | 560 | 490 | 625 | 560 | 490 | 560 | 510 | 445 | 655 | 590 | 525 | 525 | 396 | 258 | 460 | 345 | 230 | – | – | – | 425 | 330 | 230 | |
| 6 | 540 | 410 | 330 | 525 | 445 | 360 | 490 | 375 | 295 | 590 | 460 | 330 | 458 | 329 | 196 | 395 | 280 | 165 | – | – | – | 360 | 260 | 165 | |
| M | 1 | 675 | 590 | 540 | 675 | 605 | 510 | 640 | 560 | 510 | 855 | 690 | 605 | 625 | 508 | 396 | 885 | 640 | 375 | – | – | – | 820 | 605 | 375 |
| 2 | 605 | 525 | 425 | 605 | 525 | 460 | 575 | 490 | 410 | 770 | 590 | 475 | 854 | 604 | 358 | 770 | 560 | 345 | – | – | – | 720 | 525 | 330 | |
| 3 | 460 | 395 | 310 | 475 | 425 | 375 | 425 | 375 | 295 | 575 | 475 | 360 | 692 | 492 | 296 | 640 | 460 | 280 | – | – | – | 590 | 425 | 260 | |
| K | 1 | 755 | 675 | 605 | 970 | 870 | 785 | – | – | – | – | – | – | 1279 | 883 | 475 | – | – | – | – | – | – | – | – | – |
| 2 | 590 | 525 | 490 | 770 | 690 | 625 | – | – | – | – | – | – | 1000 | 692 | 375 | – | – | – | – | – | – | – | – | – | |
| 3 | 490 | 445 | 395 | 640 | 575 | 525 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| N | 1 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| 2 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| 3 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| S | 1 | 130 | 115 | 80 | – | – | – | 130 | 115 | 100 | 165 | 130 | 80 | – | – | – | 180 | 130 | 65 | – | – | – | 150 | 115 | 80 |
| 2 | 130 | 115 | 80 | – | – | – | 130 | 115 | 100 | 180 | 130 | 80 | – | – | – | 150 | 115 | 65 | – | – | – | 150 | 100 | 65 | |
| 3 | 165 | 130 | 80 | – | – | – | 165 | 130 | 100 | 215 | 150 | 100 | – | – | – | 180 | 130 | 80 | – | – | – | 165 | 130 | 80 | |
| 4 | 165 | 150 | 115 | 165 | 150 | 115 | 180 | 165 | 115 | 245 | 195 | 130 | – | – | – | 260 | 180 | 115 | – | – | – | 195 | 165 | 115 | |
| H | 1 | 395 | 295 | 230 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | 310 | 230 | 150 | – | – | – |
| 2 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | 260 | 195 | 115 | – | – | – | |
| Recommended Starting Speed are pointing to 90° Shoulder Milling . Starting Speed for Face and Copy Milling can be Increased by 20 %. As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. | |||||||||||||||||||||||||
| 7792 Series IC16 • Ramping Application Data • Curved Edges • Metric | |||||
| D1 max | ramping angle (°) | ae max plunging [mm] | Flat D1 [mm] | DH min [mm] - (min hole diameter) | DH max [mm] - (max hole diameter) |
| 40 | 2.55° | 13 | 16,3 | 50 | 78 |
| 50 | 1.36° | 13 | 26,1 | 70 | 98 |
| 52 | 1.24° | 13 | 28 | 74 | 102 |
| 63 | 0.86° | 13 | 39 | 96 | 124 |
| 66 | 0.8° | 13 | 41,9 | 102 | 130 |
| 80 | 0.58° | 13 | 55,9 | 130 | 158 |
| 100 | 0.42° | 13 | 75,9 | 170 | 198 |
| 125 | 0.32° | 13 | 100,9 | 220 | 248 |
| 160 | 0.23° | 13 | 135,8 | 290 | 318 |
| NOTE: Maximum ramp angle decreases as nose radius increases. | |||||
| 7792 Series IC16 • Ramping Application Data • Straight-Edged Inserts • Metric | |||||
| D1 max | ramping angle (°) | ae max plunging [mm] | Flat D1 [mm] | DH min [mm] - (min hole diameter) | DH max [mm] - (max hole diameter) |
| 40 | 3.7° | 12,3 | 17,85 | 50 | 78 |
| 50 | 2.25° | 12,3 | 27,72 | 70 | 98 |
| 52 | 1.65° | 12,3 | 29,82 | 74 | 102 |
| 63 | 1.4° | 12,3 | 40,8 | 96 | 124 |
| 66 | 1.3° | 12,3 | 43,7 | 102 | 130 |
| 80 | 0.8° | 12,3 | 57,7 | 130 | 158 |
| 100 | 0.65° | 12,3 | 77,53 | 170 | 198 |
| 125 | 0.5° | 12,3 | 102,5 | 220 | 248 |
| 160 | 0.27° | 12,3 | 137,46 | 290 | 318 |
| NOTE: Maximum ramp angle decreases as nose radius increases. | |||||
| 7792 Series IC16 • Programing Data • Curved Edges • Metric [mm] | |||
| IC | Corner Radius | R | L |
| 06 | 0,8 | 1,37 | 0,4 |
| 09 | 0,8 | 2,01 | 0,73 |
| 1,2 | 2,27 | 0,67 | |
| 12 | 0,8 | 2,5 | 1,02 |
| 1,2 | 2,73 | 0,97 | |
| 16 | 1,2 | 4,18 | 1,46 |
| 7792 Series IC16 • Programing Data • Straight-Edged Inserts • Metric [mm] | |||
| IC | Corner Radius | R | L |
| 06 | 0,8 | 1,46 | 0,529 |
| 09 | 0,8 | 2,13 | 1,025 |
| 1,2 | 2,25 | 0,95 | |
| 12 | 0,8 | 2,46 | 1,33 |
| 1,2 | 2,79 | 1,27 | |
| 2 | 3,42 | 1,13 | |
| 16 | 1,2 | 3,56 | 1,82 |
| CNC Program • Corner Radius Definition The use of common CAD/CAM systems requires a round insert dimension to be known for cavity machining. For finish pass applications: Wiper facet for finishing use max. feed 0,8mm. | |||
| 7792 Series IC16 • Ramping Application Data • Straight-Edged Inserts • Inch | |||||
| D1 max | ramping angle (°) | ae max plunging [Inch] | Flat D1 [Inch] | DH min [Inch] - (min hole diameter) | DH max [Inch] - (max hole diameter) |
| 1.5 | 4.53° | 0.484 | 0.628 | 1.818 | 2.921 |
| 2.0 | 2.44° | 0.484 | 1.122 | 2.818 | 3.921 |
| 2.5 | 1.51° | 0.484 | 1.626 | 3.818 | 4.921 |
| 3.0 | 0.96° | 0.484 | 2.122 | 4.818 | 5.921 |
| 4.0 | 0.62° | 0.484 | 3.114 | 6.818 | 7.921 |
| 5.0 | 0.52° | 0.484 | 4.114 | 8.818 | 9.921 |
| 6.0 | 0.32° | 0.484 | 5.115 | 10.818 | 11.921 |
| NOTE: Maximum ramp angle decreases as nose radius increases. | |||||
| 7792 Series IC16 • Ramping Application Data • Curved Edges • Inch | |||||
| D1 max | ramping angle (°) | ae max plunging [Inch] | Flat D1 [Inch] | DH min [Inch] - (min hole diameter) | DH max [Inch] - (max hole diameter) |
| 1.5 | 3° | 0.512 | 0.55 | 1.818 | 2.921 |
| 2.0 | 2.85° | 0.512 | 1.05 | 2.818 | 3.921 |
| 2.5 | 1° | 0.512 | 1.56 | 3.818 | 4.921 |
| 3.0 | 0.58° | 0.512 | 1.96 | 4.818 | 5.921 |
| 4.0 | 0.51° | 0.512 | 2.96 | 6.818 | 7.921 |
| 5.0 | 0.37° | 0.512 | 3.96 | 8.818 | 9.921 |
| 6.0 | 0.27° | 0.512 | 4.96 | 10.818 | 11.921 |
| NOTE: Maximum ramp angle decreases as nose radius increases. | |||||
| 7792 Series IC16 • Programing Data • Curved Edges • Inch [inch] | |||
| IC | Corner Radius | R | L |
| 06 | 0.031 | 0.057 | 0.016 |
| 09 | 0.031 | 0.079 | 0.028 |
| 0.047 | 0.089 | 0.026 | |
| 12 | 0.031 | 0.098 | 0.040 |
| 0.047 | 0.107 | 0.038 | |
| 16 | 0.047 | 0.164 | 0.057 |
| 7792 Series IC16 • Programing Data • Straight-Edged Inserts • Inch [inch] | |||
| IC | Corner Radius | R | L |
| 06 | 0.031 | 0.057 | 0.021 |
| 09 | 0.031 | 0.084 | 0.040 |
| 0.047 | 0.088 | 0.037 | |
| 12 | 0.031 | 0.097 | 0.052 |
| 0.047 | 0.109 | 0.050 | |
| 0.079 | 0.134 | 0.044 | |
| 16 | 0.047 | 0.140 | 0.072 |
| CNC Program • Corner Radius Definition The use of common CAD/CAM systems requires a round insert dimension to be known for cavity machining. For finish pass applications: Wiper facet for finishing use max. feed 0.031". | |||
CAD Drawings Models
Can’t find the file type you’re looking for?
Product data
I have read and accepted the Terms & Conditions of use
Katalogové číslo ISO
Katalogové číslo ANSI
to find similar products.Please select a file to download
Models
. Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.
Minimum quantity should be
| SAP Material Number | Katalogové číslo ISO | Karbid |
|---|
You are about to leave the Solution building process.
Are you sure you want to leave?