Produkt podobný k:
Břitové destičky pro KDMB • KDMB-LD
Břitové destičky
Objednací číslo4177656
ISO katalogové IDKDMB1000M0ERLDANSI katalogové IDKDMB1000M0ERLD
- K Cast Iron
- N Non-Ferrous
- S High-Temp Alloys
Sending to {{cadTool}} in progress...
Downloaded file will be available after import in the {{cadTool}} tool library.
Objednací číslo | 4177656 |
ISO katalogové ID | KDMB1000M0ERLD |
ANSI katalogové ID | KDMB1000M0ERLD |
Grade | KNS10 |
[W] Cutting Width | 25.4 mm |
[W] Cutting Width | 1 in |
[S] Insert Thickness | 4 mm |
[S] Insert Thickness | .1575 in |
[RC] Corner Radius Center | 12.7 mm |
[RC] Corner Radius Center | .5 in |
Average Chip Thickness [HM] | 0.05 mm |
Average Chip Thickness [HM] | .002 in |
Materiály obrobků
- Cast Iron
- Non-Ferrous
- High-Temp Alloys
Vlastnosti a výhody
- Vysoce přesná pozitivní geometrie.
Vytvořit řešení pro výpočet posuvů a rychlosti
Po vytvoření řešení stačí vybrat ikonu Posuvy & Rychlosti a náš systém poskytne doporučení. Informace můžete upravit přidáním zařízení a specifikací nebo provést úpravy pomocí posuvníků.
Výběr břitové destičky
KDMB Ball Nose Platform • .250"
Materiálová skupina | Lehké obrábění | Všeobecné použití | Těžké obrábění | |||
– | (Lehká geometrie) | – | (Silná geometrie) | |||
– | Odolnost proti opotřebení | Houževnatost | ||||
– | Geometrie | Sorta | Geometrie | Sorta | Geometrie | Sorta |
P1–P2 | .E..GP | KC515M | .E..GP | KC515M | .E..GP | KC515M |
P3–P4 | .E..GP | KC515M | .E..GP | KC515M | .E..GP | KC515M |
P5–P6 | .E..GP | KC515M | .E..GP | KC515M | .E..GP | KC515M |
M1–M2 | .E..GP | KC515M | .E..GP | KC515M | – | – |
M3 | .E..GP | KC515M | .E..GP | KC515M | – | – |
K1–K2 | .E..GP | KC515M | .E..GP | KC515M | – | – |
K3 | .E..GP | KC515M | .E..GP | KC515M | – | – |
N1–N2 | .E..LD | K115M | .E..LD | K115M | – | – |
N3 | .E..LD | K115M | .E..LD | K115M | – | – |
S1–S2 | – | – | – | – | – | – |
S3 | – | – | – | – | – | – |
S4 | – | – | .E..GP | KC515M | – | – |
H1 | .E..GP | KC515M | .E..GP | KC515M | – | – |
KDMB Ball Nose Platform • .312"
Materiálová skupina | Lehké obrábění | Všeobecné použití | Těžké obrábění | |||
– | (Lehká geometrie) | – | (Silná geometrie) | |||
– | Odolnost proti opotřebení | Houževnatost | ||||
– | Geometrie | Sorta | Geometrie | Sorta | Geometrie | Sorta |
P1–P2 | .E..GP | KC515M | .E..GP | KC515M | .E..GP | KC515M |
P3–P4 | .E..GP | KC505M | .E..GP | KC515M | .E..GP | KC515M |
P5–P6 | .E..GP | KC505M | .E..GP | KC515M | .E..GP | KC515M |
M1–M2 | .E..GP | KC515M | .E..GP | KC515M | – | – |
M3 | .E..GP | KC515M | .E..GP | KC515M | – | – |
K1–K2 | .E..GP | KC515M | – | – | – | – |
K3 | .E..GP | KC515M | – | – | – | – |
N1–N2 | .E..LD | K115M | .E..LD | K115M | – | – |
N3 | .E..LD | K115M | .E..LD | K115M | – | – |
S1–S2 | – | – | – | – | – | – |
S3 | – | – | – | – | – | – |
S4 | .E..LD | K115M | .E..GP | KC515M | – | – |
H1 | .E..GP | KC505M | .E..GP | KC505M | .E..GP | KC515M |
KDMB Ball Nose Platform • .375"
Materiálová skupina | Lehké obrábění | Všeobecné použití | Těžké obrábění | |||
– | (Lehká geometrie) | – | (Silná geometrie) | |||
– | Odolnost proti opotřebení | Houževnatost | ||||
– | Geometrie | Sorta | Geometrie | Sorta | Geometrie | Sorta |
P1–P2 | .E..GP | KC515M | .E..GP | KC515M | .E..GP | KC515M |
P3–P4 | .E..GP | KC505M | .E..GP | KC515M | .E..GP | KC515M |
P5–P6 | .E..GP | KC505M | .E..GP | KC515M | .E..GP | KC515M |
M1–M2 | .E..GP | KC515M | .E..GP | KC515M | – | – |
M3 | .E..GP | KC515M | .E..GP | KC515M | – | – |
K1–K2 | .E..GP | KC515M | .E..GP | KC515M | – | – |
K3 | .E..GP | KC515M | .E..GP | KC515M | – | – |
N1–N2 | .E..LD | K115M | .E..LD | K115M | – | – |
N3 | .E..LD | K115M | .E..LD | K115M | – | – |
S1–S2 | – | – | – | – | – | – |
S3 | – | – | – | – | – | – |
S4 | .E..LD | K115M | .E..GP | KC515M | – | – |
H1 | .E..GP | KC505M | .E..GP | KC505M | .E..GP | KC515M |
KDMB Ball Nose Platform • .500"
Materiálová skupina | Lehké obrábění | Všeobecné použití | Těžké obrábění | |||
– | (Lehká geometrie) | – | (Silná geometrie) | |||
– | Odolnost proti opotřebení | Houževnatost | ||||
– | Geometrie | Sorta | Geometrie | Sorta | Geometrie | Sorta |
P1–P2 | .E..GP | KC515M | .E..GP | KC515M | .E..HC | KC530M |
P3–P4 | .E..GP | KC505M | .E..GP | KC515M | .E..HC | KC530M |
P5–P6 | .E..GP | KC505M | .E..GP | KC515M | .E..HC | KC530M |
M1–M2 | .E..GP | KC515M | .E..HC | KC530M | .E..HC | KC530M |
M3 | .E..GP | KC515M | .E..HC | KC530M | .E..HC | KC530M |
K1–K2 | .E..GP | KC515M | .E..GN | KC515M | .E..GN | KC515M |
K3 | .E..GP | KC515M | .E..GN | KC515M | .E..GN | KC515M |
N1–N2 | .E..LD | K115M | .E..LD | K115M | – | – |
N3 | .E..LD | K115M | .E..LD | K115M | – | – |
S1–S2 | – | – | – | – | – | – |
S3 | – | – | – | – | – | – |
S4 | .E..LD | K115M | .E..GP | KC515M | .E..HC | KC530M |
H1 | .E..GP | KC505M | .E..GP | KC505M | .E..GN | KC515M |
KDMB Ball Nose Platform • .625"
Materiálová skupina | Lehké obrábění | Všeobecné použití | Těžké obrábění | |||
– | (Lehká geometrie) | – | (Silná geometrie) | |||
– | Odolnost proti opotřebení | Houževnatost | ||||
– | Geometrie | Sorta | Geometrie | Sorta | Geometrie | Sorta |
P1–P2 | .E..GP | KC515M | .E..GP | KC515M | .E..HC | KC530M |
P3–P4 | .E..GP | KC505M | .E..GP | KC515M | .E..HC | KC530M |
P5–P6 | .E..GP | KC505M | .E..GP | KC515M | .E..HC | KC530M |
M1–M2 | .E..GP | KC515M | .E..HC | KC530M | .E..HC | KC530M |
M3 | .E..GP | KC515M | .E..HC | KC530M | .E..HC | KC530M |
K1–K2 | .E..GP | KC515M | .E..GP | KC515M | – | – |
K3 | .E..GP | KC515M | .E..GP | KC515M | – | – |
N1–N2 | .E..LD | K115M | .E..LD | K115M | – | – |
N3 | .E..LD | K115M | .E..LD | K115M | – | – |
S1–S2 | – | – | – | – | – | – |
S3 | – | – | – | – | – | – |
S4 | .E..LD | K115M | .E..GP | KC515M | .E..HC | KC530M |
H1 | .E..GP | KC505M | .E..GP | KC505M | .E..GP | KC515M |
KDMB Ball Nose Platform • .750"
Materiálová skupina | Lehké obrábění | Všeobecné použití | Těžké obrábění | |||
– | (Lehká geometrie) | – | (Silná geometrie) | |||
– | Odolnost proti opotřebení | Houževnatost | ||||
– | Geometrie | Sorta | Geometrie | Sorta | Geometrie | Sorta |
P1–P2 | .E..GP | KC515M | .E..GP | KC515M | .E..HC | KC530M |
P3–P4 | .E..GP | KC505M | .E..GP | KC515M | .E..HC | KC530M |
P5–P6 | .E..GP | KC505M | .E..GP | KC515M | .E..HC | KC530M |
M1–M2 | .E..GP | KC515M | .E..HC | KC530M | .E..HC | KC530M |
M3 | .E..GP | KC515M | .E..HC | KC530M | .E..HC | KC530M |
K1–K2 | .E..GP | KC515M | .E..GN | KC515M | .E..GN | KC515M |
K3 | .E..GP | KC515M | .E..GN | KC515M | .E..GN | KC515M |
N1–N2 | .E..LD | K115M | .E..LD | K115M | – | – |
N3 | .E..LD | K115M | .E..LD | K115M | – | – |
S1–S2 | – | – | – | – | – | – |
S3 | – | – | – | – | – | – |
S4 | .E..LD | K115M | .E..GP | KC515M | .E..HC | KC530M |
H1 | .E..GP | KC505M | .E..GP | KC505M | .E..GN | KC515M |
KDMB Ball Nose Platform • 1.00"
Materiálová skupina | Lehké obrábění | Všeobecné použití | Těžké obrábění | |||
– | (Lehká geometrie) | – | (Silná geometrie) | |||
– | Odolnost proti opotřebení | Houževnatost | ||||
– | Geometrie | Sorta | Geometrie | Sorta | Geometrie | Sorta |
P1–P2 | .E..GP | KC515M | .E..GP | KC515M | .E..HC | KC530M |
P3–P4 | .E..GP | KC505M | .E..GP | KC515M | .E..HC | KC530M |
P5–P6 | .E..GP | KC505M | .E..GP | KC515M | .E..HC | KC530M |
M1–M2 | .E..GP | KC515M | .E..HC | KC530M | .E..HC | KC530M |
M3 | .E..GP | KC515M | .E..HC | KC530M | .E..HC | KC530M |
K1–K2 | .E..GP | KC515M | .E..GN | KC515M | .E..GN | KC515M |
K3 | .E..GP | KC515M | .E..GN | KC515M | .E..GN | KC515M |
N1–N2 | .E..LD | K115M | .E..LD | K115M | – | – |
N3 | .E..LD | K115M | .E..LD | K115M | – | – |
S1–S2 | – | – | – | – | – | – |
S3 | – | – | – | – | – | – |
S4 | .E..LD | K115M | .E..GP | KC515M | .E..HC | KC530M |
H1 | .E..GP | KC505M | .E..GP | KC505M | .E..GN | KC515M |
KDMB Ball Nose Platform • 1.25"
Materiálová skupina | Lehké obrábění | Všeobecné použití | Těžké obrábění | |||
– | (Lehká geometrie) | – | (Silná geometrie) | |||
– | Odolnost proti opotřebení | Houževnatost | ||||
– | Geometrie | Sorta | Geometrie | Sorta | Geometrie | Sorta |
P1–P2 | .E..GP | KC515M | .E..GP | KC515M | .E..GP | KC515M |
P3–P4 | .E..GP | KC505M | .E..GP | KC515M | .E..GP | KC515M |
P5–P6 | .E..GP | KC505M | .E..GP | KC515M | .E..GP | KC515M |
M1–M2 | .E..GP | KC515M | .E..GP | KC515M | – | – |
M3 | .E..GP | KC515M | .E..GP | KC515M | – | – |
K1–K2 | .E..GP | KC515M | – | – | – | – |
K3 | .E..GP | KC515M | – | – | – | – |
N1–N2 | .E..LD | K115M | .E..LD | K115M | – | – |
N3 | .E..LD | K115M | .E..LD | K115M | – | – |
S1–S2 | – | – | – | – | – | – |
S3 | – | – | – | – | – | – |
S4 | .E..LD | K115M | .E..GP | KC515M | ||
H1 | .E..GP | KC505M | .E..GP | KC505M | .E..GP | KC515M |
Posuvy
KDMB Ball Nose • .250"
Pracovní průměr (Dw) při axiální hloubce řezu (ap) | ||||
D1 max | ||||
At .125 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..LD |
.E..GP | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..GP |
At .050 Axial Depth of Cut (ap)
Lehké obrábění | Všeobecné použití | Těžké obrábění |
At .025 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..LD |
.E..GP | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..GP |
At .013 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..LD |
.E..GP | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..GP |
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .006 | .008 | .015 | .004 | .006 | .011 | .004 | .005 | .010 | .004 | .005 | .009 | .004 | .005 | .009 | .E..LD |
.E..GP | .006 | .008 | .015 | .004 | .006 | .011 | .004 | .005 | .010 | .004 | .005 | .009 | .004 | .005 | .009 | .E..GP |
KDMB Ball Nose • .312"
Pracovní průměr (Dw) při axiální hloubce řezu (ap) | ||||
D1 max | ||||
At .156 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..LD |
.E..GP | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..GP |
At .047 Axial Depth of Cut (ap)
Lehké obrábění | Všeobecné použití | Těžké obrábění |
At .031 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..LD |
.E..GP | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..GP |
At .016 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..LD |
.E..GP | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..GP |
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..LD |
.E..GP | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..GP |
KDMB Ball Nose • .375"
Pracovní průměr (Dw) při axiální hloubce řezu (ap) | ||||
D1 max | ||||
At .188 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..LD |
.E..GP | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..GP |
At .056 Axial Depth of Cut (ap)
Lehké obrábění | Všeobecné použití | Těžké obrábění |
At .038 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..LD |
.E..GP | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..GP |
At .019 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..LD |
.E..GP | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..GP |
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..LD |
.E..GP | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..GP |
KDMB Ball Nose • .500"
Pracovní průměr (Dw) při axiální hloubce řezu (ap) | ||||
D1 max | ||||
At .250 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..LD |
.E..GP | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..GP |
.E..GN | .007 | .010 | .018 | .005 | .008 | .013 | .004 | .007 | .011 | .004 | .006 | .011 | .004 | .006 | .011 | .E..GN |
.E..HC | .007 | .014 | .024 | .005 | .010 | .018 | .004 | .009 | .015 | .004 | .008 | .014 | .004 | .008 | .014 | .E..HC |
At .075 Axial Depth of Cut (ap)
Lehké obrábění | Všeobecné použití | Těžké obrábění |
At .050 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..LD |
.E..GP | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..GP |
.E..GN | .016 | .024 | .042 | .012 | .017 | .031 | .010 | .015 | .026 | .009 | .014 | .025 | .009 | .014 | .024 | .E..GN |
.E..HC | .016 | .032 | .057 | .012 | .023 | .041 | .010 | .020 | .035 | .009 | .019 | .033 | .009 | .018 | .032 | .E..HC |
At .025 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..LD |
.E..GP | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..GP |
.E..GN | .009 | .014 | .025 | .007 | .011 | .019 | .006 | .009 | .016 | .006 | .009 | .015 | .006 | .008 | .015 | .E..GN |
.E..HC | .009 | .019 | .034 | .007 | .014 | .025 | .006 | .012 | .021 | .006 | .011 | .020 | .006 | .011 | .020 | .E..HC |
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..LD |
.E..GP | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..GP |
.E..GN | .011 | .017 | .030 | .008 | .013 | .022 | .007 | .011 | .019 | .007 | .010 | .018 | .007 | .010 | .018 | .E..GN |
.E..HC | .011 | .023 | .041 | .008 | .017 | .030 | .007 | .015 | .026 | .007 | .014 | .024 | .007 | .013 | .023 | .E..HC |
KDMB Ball Nose • .625"
Pracovní průměr (Dw) při axiální hloubce řezu (ap) | ||||
D1 max | ||||
At .313 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..LD |
.E..GP | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..GP |
.E..HC | .007 | .014 | .024 | .005 | .010 | .018 | .004 | .009 | .015 | .004 | .008 | .014 | .004 | .008 | .014 | .E..HC |
At .094 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..LD |
.E..GP | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..GP |
.E..HC | .009 | .019 | .034 | .007 | .014 | .025 | .006 | .012 | .021 | .006 | .011 | .020 | .006 | .011 | .020 | .E..HC |
At .063 Axial Depth of Cut (ap)
Lehké obrábění | Všeobecné použití | Těžké obrábění |
At .031 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..LD |
.E..GP | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..GP |
.E..HC | .016 | .032 | .057 | .012 | .023 | .041 | .010 | .020 | .035 | .009 | .019 | .033 | .009 | .018 | .032 | .E..HC |
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..LD |
.E..GP | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..GP |
.E..HC | .011 | .023 | .041 | .008 | .017 | .030 | .007 | .015 | .026 | .007 | .014 | .024 | .007 | .013 | .023 | .E..HC |
KDMB Ball Nose • .750"
Pracovní průměr (Dw) při axiální hloubce řezu (ap) | ||||
D1 max | ||||
At .375 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..LD |
.E..GP | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..GP |
.E..GN | .007 | .010 | .018 | .005 | .008 | .013 | .004 | .007 | .011 | .004 | .006 | .011 | .004 | .006 | .011 | .E..GN |
.E..HC | .007 | .014 | .024 | .005 | .010 | .018 | .004 | .009 | .015 | .004 | .008 | .014 | .004 | .008 | .014 | .E..HC |
At .113 Axial Depth of Cut (ap)
Lehké obrábění | Všeobecné použití | Těžké obrábění |
At .075 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..LD |
.E..GP | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..GP |
.E..GN | .009 | .014 | .025 | .007 | .011 | .019 | .006 | .009 | .016 | .006 | .009 | .015 | .006 | .008 | .015 | .E..GN |
.E..HC | .009 | .019 | .034 | .007 | .014 | .025 | .006 | .012 | .021 | .006 | .011 | .020 | .006 | .011 | .020 | .E..HC |
At .038 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..LD |
.E..GP | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..GP |
.E..GN | .016 | .024 | .042 | .012 | .017 | .031 | .010 | .015 | .026 | .009 | .014 | .025 | .009 | .014 | .024 | .E..GN |
.E..HC | .016 | .032 | .057 | .012 | .023 | .041 | .010 | .020 | .035 | .009 | .019 | .033 | .009 | .018 | .032 | .E..HC |
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..LD |
.E..GP | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..GP |
.E..GN | .011 | .017 | .030 | .008 | .013 | .022 | .007 | .011 | .019 | .007 | .010 | .018 | .007 | .010 | .018 | .E..GN |
.E..HC | .011 | .023 | .041 | .008 | .017 | .030 | .007 | .015 | .026 | .007 | .014 | .024 | .007 | .013 | .023 | .E..HC |
KDMB Ball Nose • 1.00"
Pracovní průměr (Dw) při axiální hloubce řezu (ap) | ||||
D1 max | ||||
At .500 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..LD |
.E..GP | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..GP |
.E..GN | .007 | .010 | .018 | .005 | .008 | .013 | .004 | .007 | .011 | .004 | .006 | .011 | .004 | .006 | .011 | .E..GN |
.E..HC | .007 | .014 | .024 | .005 | .010 | .018 | .004 | .009 | .015 | .004 | .008 | .014 | .004 | .008 | .014 | .E..HC |
At .150 Axial Depth of Cut (ap)
Lehké obrábění | Všeobecné použití | Těžké obrábění |
At .100 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..LD |
.E..GP | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..GP |
.E..GN | .009 | .014 | .025 | .007 | .011 | .019 | .006 | .009 | .016 | .006 | .009 | .015 | .006 | .008 | .015 | .E..GN |
.E..HC | .009 | .019 | .034 | .007 | .014 | .025 | .006 | .012 | .021 | .006 | .011 | .020 | .006 | .011 | .020 | .E..HC |
At .050 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..LD |
.E..GP | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..GP |
.E..GN | .016 | .024 | .042 | .012 | .017 | .031 | .010 | .015 | .026 | .009 | .014 | .025 | .009 | .014 | .024 | .E..GN |
.E..HC | .016 | .032 | .057 | .012 | .023 | .041 | .010 | .020 | .035 | .009 | .019 | .033 | .009 | .018 | .032 | .E..HC |
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..LD |
.E..GP | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..GP |
.E..GN | .011 | .017 | .030 | .008 | .013 | .022 | .007 | .011 | .019 | .007 | .010 | .018 | .007 | .010 | .018 | .E..GN |
.E..HC | .011 | .023 | .041 | .008 | .017 | .030 | .007 | .015 | .026 | .007 | .014 | .024 | .007 | .013 | .023 | .E..HC |
KDMB Ball Nose • 1.25"
Pracovní průměr (Dw) při axiální hloubce řezu (ap) | ||||
D1 max | ||||
At .625 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..LD |
.E..GP | .005 | .007 | .012 | .004 | .005 | .009 | .003 | .004 | .008 | .003 | .004 | .007 | .003 | .004 | .007 | .E..GP |
At .188 Axial Depth of Cut (ap)
Lehké obrábění | Všeobecné použití | Těžké obrábění |
At .125 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..LD |
.E..GP | .011 | .016 | .028 | .008 | .012 | .020 | .007 | .010 | .018 | .007 | .009 | .016 | .006 | .009 | .016 | .E..GP |
At .063 Axial Depth of Cut (ap)
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..LD |
.E..GP | .008 | .011 | .020 | .006 | .008 | .015 | .005 | .007 | .013 | .005 | .007 | .012 | .005 | .007 | .012 | .E..GP |
Geometrie břitových destiček | Doporučené počáteční posuvy na zub (Fz) podle % poměru radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
.E..LD | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..LD |
.E..GP | .007 | .009 | .017 | .005 | .007 | .012 | .004 | .006 | .011 | .004 | .006 | .010 | .004 | .006 | .010 | .E..GP |
Rychlosti
Recommended Starting Speeds [SFM]
Materiálová skupina | K115M | KC505M | KC515M | KC530M | |||||||||
P | 1 | – | – | – | – | – | – | 1080 | 960 | 840 | 900 | 780 | 660 |
2 | – | – | – | – | – | – | 1020 | 900 | 780 | 780 | 660 | 540 | |
3 | – | – | – | – | – | – | 900 | 780 | 660 | 660 | 600 | 540 | |
4 | – | – | – | 1180 | 860 | 710 | 780 | 660 | 540 | 600 | 540 | 480 | |
5 | – | – | – | 1180 | 860 | 710 | 660 | 540 | 420 | 540 | 480 | 420 | |
6 | – | – | – | 1140 | 780 | 620 | 540 | 420 | 360 | 420 | 360 | 300 | |
M | 1 | – | – | – | – | – | – | 1080 | 900 | 780 | 900 | 720 | 600 |
2 | – | – | – | – | – | – | 900 | 720 | 540 | 600 | 480 | 420 | |
3 | – | – | – | – | – | – | 720 | 600 | 480 | 480 | 420 | 360 | |
K | 1 | 720 | 600 | 480 | – | – | – | 1440 | 1080 | 720 | – | – | – |
2 | 600 | 480 | 360 | – | – | – | 1080 | 840 | 600 | – | – | – | |
3 | 360 | 300 | 240 | – | – | – | 480 | 360 | 240 | – | – | – | |
N | 1–2 | 1440 | 1080 | 720 | – | – | – | – | – | – | – | – | – |
3 | 960 | 720 | 600 | – | – | – | – | – | – | – | – | – | |
S | 1 | – | – | – | – | – | – | – | – | – | – | – | – |
2 | – | – | – | – | – | – | – | – | – | – | – | – | |
3 | – | – | – | – | – | – | – | – | – | – | – | – | |
4 | 300 | 230 | 160 | – | – | – | – | – | – | 260 | 200 | 170 | |
H | 1 | – | – | – | 860 | 670 | 550 | 550 | 400 | 310 | – | – | – |
CAD Drawings Models
Can’t find the file type you’re looking for?
Product data
I have read and accepted the Terms & Conditions of use