Foratura
Foratura: Ingresso inclinato
Foratura: Uscita inclinata
Foratura: Offset sull'asse x
Foratura: Convessa
Codolo — Cilindrico con piano e flangia
Adduzione interna di refrigerante: Radiale: Foratura intercambiabile
Foratura: Foro cieco
Chain Drilling
Drilling: Cross-Hole Drilling
Drilling: Half-Cylindrical Drilling
Drilling: Corner Drilling 45°Downloaded file will be available after import in the {{cadTool}} tool library.
| Material Number | 2036648 |
| ISO Catalog ID | DFR0844R3SSF100 |
| ANSI Catalog ID | DFR0844R3SSF100 |
| [D] Dia adattatore / stelo / foro | 25.4 mm |
| [D] Dia adattatore / stelo / foro | 1 in |
| [D1] Diametro punta M | 21.438 mm |
| [D1] Diametro punta M | .844 in |
| [D1max] Diametro punta massimo | 22.438 mm |
| [D1max] Diametro punta massimo | .8834 in |
| [L1] Lunghezza spessore inserto | 92.648 mm |
| [L1] Lunghezza spessore inserto | 3.647 in |
| [L4] Profondità di foratura massima | 64.313 mm |
| [L4] Profondità di foratura massima | 2.532 in |
| [L5] Lunghezza punta | 0.755 mm |
| [L5] Lunghezza punta | .0297 in |
| [LS] Lunghezza del codolo | 76.2 mm |
| [LS] Lunghezza del codolo | 3 in |
| Inserto di riferimento | DFR0403. |
ForaturaForatura: Ingresso inclinatoForatura: Uscita inclinataForatura: Offset sull'asse xForatura: ConvessaCodolo — Cilindrico con piano e flangiaAdduzione interna di refrigerante: Radiale: Foratura intercambiabileForatura: Foro ciecoChain DrillingDrilling: Cross-Hole DrillingDrilling: Half-Cylindrical DrillingDrilling: Corner Drilling 45°Crea una soluzione per calcolare avanzamenti e velocità
Dopo aver creato una soluzione, basta scegliere l'icona Avanzamento e Velocità e il nostro sistema fornirà dei suggerimenti. Puoi personalizzare le informazioni aggiungendo la tua macchina e le specifiche o apportare delle modifiche utilizzando i cursori.
| WARNING During through-hole operations, a slug or disc is produced as the tool breaks through the workpiece. When the drill is stationary and the workpiece is rotating, this slug may be hurled from the chuck by centrifugal force. Provide adequate shielding to protect bystanders. |
| D | LS |
| 20 | 50 |
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500–.625" | DFR03... .688–.750" | DFR04... .813–1.00" | ||||||
| P | 1 | S | O | MD | KCU25 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | GD | KCPK10 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| 3 | S | O | GD | KCPK10 | 853 | 935 | 1050 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 590 | 640 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 361 | 394 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| 4 | S | O | GD | KCU25 | 722 | 820 | 984 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 492 | 590 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 295 | 361 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| 5 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .003–.005 | .004–.006 | .004–.007 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .003–.005 | .004–.006 | .004–.007 | ||
| I | LD | KC7140 | ||||||||||
| 6 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| P | 1 | S | O | MD | KCU25 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 |
| 1 | S | I | MD | KC7140 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | U | O | MD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | U | I | MD | KC7140 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | I | I | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | S | O | GD | KCPK10 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | S | I | LD | KC7140 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | U | O | GD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | U | I | LD | KC7140 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | I | I | LD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | S | O | GD | KCPK10 | 853 | 935 | 1050 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | S | I | LD | KC7140 | 853 | 935 | 1050 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | U | O | GD | KCU40 | 590 | 640 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | U | I | LD | KC7140 | 590 | 640 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | I | O | GD | KC7140 | 361 | 394 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | I | I | LD | KC7140 | 361 | 394 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | S | O | GD | KCU25 | 722 | 820 | 984 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | S | I | LD | KC7140 | 722 | 820 | 984 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | U | O | GD | KCU40 | 492 | 590 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | U | I | LD | KC7140 | 492 | 590 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | I | O | GD | KC7140 | 295 | 361 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | I | I | LD | KC7140 | 295 | 361 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 5 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | S | I | LD | KC7140 | 590 | 656 | 722 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | U | I | LD | KC7140 | 394 | 443 | 492 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | I | I | LD | KC7140 | 230 | 279 | 328 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 6 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | S | I | LD | KC7140 | 590 | 656 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | U | I | LD | KC7140 | 394 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | I | I | LD | KC7140 | 230 | 279 | 328 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500–.625" | DFR03... .688–.750" | DFR04... .813–1.00" | ||||||
| M | 1 | S | O | MD | KC7140 | 492 | 623 | 754 | SFM | .003–.005 | .003–.006 | .004–.007 |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | MD | KC7140 | 492 | 590 | 689 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| 3 | S | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 262 | 361 | 459 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 164 | 230 | 295 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| M | 1 | S | O | MD | KC7140 | 492 | 623 | 754 | SFM | .003–.005 | .003–.006 | .004–.007 |
| 1 | S | I | MD | KC7140 | 492 | 623 | 754 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | U | I | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | I | I | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | S | O | MD | KC7140 | 492 | 590 | 689 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | S | I | MD | KC7140 | 492 | 590 | 689 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | U | I | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | I | I | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | S | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | S | I | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | U | O | MD | KC7140 | 262 | 361 | 459 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | U | I | MD | KC7140 | 262 | 361 | 459 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | I | O | MD | KC7140 | 164 | 230 | 295 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | I | I | MD | KC7140 | 164 | 230 | 295 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| Inch | ||||||||||||
| Material | Pocket Seat | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500–.625" | DFR03... .688–.750" | DFR04... .813–1.00" | ||||||
| K | 1 | S | O | GD | KCPK10 | 656 | 787 | 984 | SFM | .004–.007 | .005–.008 | .006–.009 |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 394 | 508 | 656 | SFM | .004–.007 | .005–.008 | .006–.009 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 262 | 328 | 410 | SFM | .004–.007 | .005–.008 | .005–.009 | ||
| I | LD | KC7140 | ||||||||||
| 2 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .005–.009 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .006–.009 | ||
| I | LD | KC7140 | ||||||||||
| 3 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .006–.009 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .005–.009 | ||
| I | LD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| K | 1 | S | O | GD | KCPK10 | 656 | 787 | 984 | SFM | .004–.007 | .005–.008 | .006–.009 |
| 1 | S | I | LD | KCU40 | 656 | 787 | 984 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 1 | U | O | GD | KCU25 | 394 | 508 | 656 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 1 | U | I | LD | KC7140 | 394 | 508 | 656 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 1 | I | O | GD | KCU40 | 262 | 328 | 410 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 1 | I | I | LD | KC7140 | 262 | 328 | 410 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 2 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 2 | S | I | LD | KCU40 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 2 | U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 2 | U | I | LD | KC7140 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 2 | I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 2 | I | I | LD | KC7140 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 3 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 3 | S | I | LD | KCU40 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 3 | U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 3 | U | I | LD | KC7140 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 3 | I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 3 | I | I | LD | KC7140 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | ||||||
| N | 1 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 984 | 1312 | 1640 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 2 | S | O | ST | KD1425 | 1230 | 1804 | 2542 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 574 | 820 | 1066 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 3 | S | O | ST | KD1425 | 1148 | 1640 | 2132 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 492 | 820 | 1148 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 4 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 820 | 1148 | 1486 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 5 | S | O | HP | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | HP | KD1425 | ||||||||||
| U | O | HP | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | HP | KCU40 | ||||||||||
| I | O | HP | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | HP | KCU40 | ||||||||||
| 6 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | GD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | GD | KCU40 | ||||||||||
| I | O | GD | KMF | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | GD | KMF | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| N | 1 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 |
| 1 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | U | O | LD | KCU40 | 984 | 1312 | 1640 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | U | I | LD | KCU40 | 984 | 1312 | 1640 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | I | I | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | S | O | ST | KD1425 | 1230 | 1804 | 2542 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | S | I | ST | KD1425 | 1230 | 1804 | 2542 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | U | I | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | I | O | LD | KCU40 | 574 | 820 | 1066 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | I | I | LD | KCU40 | 574 | 820 | 1066 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | S | O | ST | KD1425 | 1148 | 1640 | 2132 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | S | I | ST | KD1425 | 1148 | 1640 | 2132 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | U | I | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | I | O | LD | KCU40 | 492 | 820 | 1148 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | I | I | LD | KCU40 | 492 | 820 | 1148 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | U | O | LD | KCU40 | 820 | 1148 | 1486 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | U | I | LD | KCU40 | 820 | 1148 | 1486 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | I | I | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | S | O | HP | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | S | I | HP | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | U | O | HP | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | U | I | HP | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | I | O | HP | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | I | I | HP | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | U | I | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | I | O | LD | KMF | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | I | I | LD | KMF | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500 | DFR03... .688 | DFR04... .813 | ||||||
| S | 1 | S | O | GD | KCU40 | 197 | 230 | 246 | SFM | .002–.002 | .002–.003 | .002–.004 |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 131 | 164 | 197 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 98 | 131 | 164 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| 3 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.004 | .002–.003 | .002–.004 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| 4 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"-.625" | DFR03... .688"-.750" | DFR04... .813"-1.00" | |
| S | 1 | S | O | GD | KCU40 | 197 | 230 | 246 | SFM | .002–.002 | .002–.003 | .002–.004 |
| 1 | S | I | LD | KCU40 | 197 | 230 | 246 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | U | O | GD | KCU40 | 131 | 164 | 197 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | U | I | LD | KC7140 | 131 | 164 | 197 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | I | I | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | S | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | S | I | LD | KCU40 | 164 | 197 | 230 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | U | O | GD | KCU40 | 98 | 131 | 164 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | U | I | LD | KC7140 | 98 | 131 | 164 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | I | I | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 3 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.004 | .002–.003 | .002–.004 | |
| 3 | S | I | LD | KCU40 | 230 | 262 | 295 | SFM | .002–.004 | .002–.003 | .002–.004 | |
| 3 | U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 3 | U | I | LD | KC7140 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 3 | I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 3 | I | I | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | S | I | LD | KCU40 | 230 | 262 | 295 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | U | I | LD | KC7140 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | I | I | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| Metric | ||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||
| Range | ||||||||||
| Min | Starting Value | Max | Ø | DFR04 20,50–24,00mm | ||||||
| N | 1 | S | O | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 |
| I | ST | KD1425 | ||||||||
| 2 | S | O | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 3 | S | O | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 4 | S | O | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 5 | S | O | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
| I | ST | KD1425 | ||||||||
| Inch | ||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||
| Range | ||||||||||
| Min | Starting Value | Max | Ø | DFR04 .813–1.00" | ||||||
| N | 1 | S | O | ST | KD1425 | 1300 | 2362 | 2760 | IPR | .002–.003 |
| I | ST | KD1425 | ||||||||
| 2 | S | O | ST | KD1425 | 1209 | 2197 | 2567 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 3 | S | O | ST | KD1425 | 1118 | 2032 | 2374 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 4 | S | O | ST | KD1425 | 1560 | 2362 | 2760 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 5 | S | O | ST | KD1425 | 1575 | 2362 | 2834 | IPR | .002–.003 | |
| I | ST | KD1425 | ||||||||
| Metric | ||||||||||
| Cutting Speed | ||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR04 20,50–24,00 mm | |
| N | 1 | S | O | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 |
| 1 | S | I | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 | |
| 2 | S | O | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| 2 | S | I | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| 3 | S | O | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| 3 | S | I | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| 4 | S | O | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| 4 | S | I | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| 5 | S | O | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
| 5 | S | I | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
I have read and accepted the Terms & Conditions of use
ISO Catalogo
ANSI Catalogo
to find similar products.Please select a file to download
Models
. Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.
Minimum quantity should be
| SAP Material Number | ISO Catalogo | Grade |
|---|
You are about to leave the Solution building process.
Are you sure you want to leave?