KSSM 8+ • Fresas de planear • IC 10 mm • Sistema métrico
Producto similar a:
KSSM 8+ • Fresas de planear • IC 10 mm • Sistema métrico
Fresas de mango intercambiables
Número de material100147720
Póngase en contacto con nuestro equipo de ventas para descubrir todas sus opciones de precios
Features and benefits
- Fresa de ángulo de ataque de 88°.
- Plaquita de doble extremo.
- Ocho filos de corte ofrecen un coste inferior por filo.
- Acción de corte suave con fuerzas de corte bajas.
- Excelente opción para una configuración de accesorios débiles y un largo alcance de la herramienta.
Planeado
Ranurado: Placa cuadrada
Fresado lateral/Fresado en escuadra: Placa cuadrada
Fresado — Con refrigeración interna
Fresado — lateral y planeado
Guía para la selección de plaquitas
| KSSM8+™ • IC10 • Insert Selection Guide | ||||||
| Grupo de materiales | Mecanizado ligero | Aplicaciones generales | Mecanizado intensivo | |||
| (Geometría ligera) | (Geometría fuerte) | |||||
| resistencia |  | tenacidad | ||||
| Geometría | Calidad | Geometría | Calidad | Geometría | Calidad | |
| P1–P2 | .E..LD | KC725M | .S..GD | KCPK30 | .S..GD | KCPM40 |
| P3–P4 | .E..LD | KCPK30 | .S..GD | KCPK30 | .S..GD | KCPK30 |
| P5–P6 | .E..LD | KC725M | .S..GD | KCPM40 | .S..GD | KCPM40 |
| M1–M2 | .E..LD | KC725M | .E..LD | KC725M | .S..GD | KCPM40 |
| M3 | .E..LD | KC725M | .S..GD | KCPM40 | .S..GD | KCPM40 |
| K1–K2 | .E..LD | KCK20B | .S..GD | KCK15 | .S..GD | KCK15 |
| K3 | .E..LD | KCK20B | .S..GD | KCK15 | .S..GD | KCPK30 |
| N1–N2 | – | – | – | – | – | – |
| N3 | – | – | – | – | – | – |
| S1–S2 | .E..LD | KC725M | .E..LD | KC725M | .E..LD | KC725M |
| S3 | .E..LD | KC725M | .E..LD | KC725M | .S..GD | KCPM40 |
| S4 | .E..LD | KC725M | .E..LD | KC725M | .E..LD | KC725M |
| H1 | – | – | – | – | – | – |
Avances iniciales recomendados [mm]
| Avances iniciales recomendados [mm] | ||||||
| Geometría de plaquita | Avance inicial recomendado por diente (Fz) en relación con % de contacto radial (ae) | |||||
| 30% | 40–100% | |||||
| L | M | H | L | M | H | |
| .E..LD | 0,08 | 0,19 | 0,33 | 0,08 | 0,18 | 0,30 |
| .S..GD | 0,11 | 0,24 | 0,38 | 0,10 | 0,22 | 0,35 |
| NOTA: Utilice los valores de "mecanizado ligero" como avance inicial. | ||||||
| KSSM8+™ • IC10 Inch • Recommended Starting Feeds [IPT] | ||||||
| Geometría de plaquita | Avance inicial recomendado por diente (Fz) en relación con % de contacto radial (ae) | |||||
| 30% | 40–100% | |||||
| L | M | H | L | M | H | |
| .E..LD | 0.003 | 0.008 | 0.013 | 0.003 | 0.007 | 0.012 |
| .S..GD | 0.004 | 0.009 | 0.015 | 0.004 | 0.009 | 0.014 |
| L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use "Light Machining" values as starting feed rate. | ||||||
Velocidades iniciales recomendadas (m/min)
| Velocidades iniciales recomendadas (m/min) | ||||||||||||||||
| Calidad | KC725M | KCK15 | KCPK30 | KCK20B | KCPM40 | |||||||||||
| Grosor de viruta hex mm | Mín | Máx. | Mín | Máx. | Mín | Máx. | Mín | Máx. | Mín | Máx. | ||||||
| Grupo de materiales | Máx. | Inicio | Mín | Máx. | Inicio | Mín | Máx. | Inicio | Mín | Máx. | Inicio | Mín | Máx. | Inicio | Mín | |
| P | 1 | 260 | 230 | 215 | – | – | – | 455 | 395 | 370 | – | – | – | 295 | 260 | 245 |
| 2 | 220 | 190 | 160 | – | – | – | 280 | 255 | 230 | – | – | – | 250 | 215 | 180 | |
| 3 | 200 | 170 | 140 | – | – | – | 255 | 230 | 205 | – | – | – | 230 | 195 | 160 | |
| 4 | 180 | 150 | 120 | – | – | – | 225 | 185 | 160 | – | – | – | 205 | 170 | 135 | |
| 5 | 150 | 135 | 120 | – | – | – | 190 | 170 | 150 | – | – | – | 170 | 155 | 135 | |
| 6 | 130 | 100 | 80 | – | – | – | 160 | 135 | 110 | – | – | – | 150 | 115 | 90 | |
| M | 1 | 170 | 150 | 135 | – | – | – | 205 | 185 | 155 | – | – | – | 195 | 170 | 155 |
| 2 | 155 | 130 | 110 | – | – | – | 185 | 160 | 140 | – | – | – | 175 | 150 | 125 | |
| 3 | 115 | 100 | 80 | – | – | – | 145 | 130 | 115 | – | – | – | 130 | 115 | 90 | |
| K | 1 | – | – | – | 420 | 385 | 340 | 295 | 265 | 240 | 360 | 290 | 245 | – | – | – |
| 2 | – | – | – | 335 | 295 | 275 | 235 | 210 | 190 | 280 | 230 | 195 | – | – | – | |
| 3 | – | – | – | 280 | 250 | 230 | 195 | 175 | 160 | 210 | 175 | 140 | – | – | – | |
| N | 1 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| 2 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| 3 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| S | 1 | 35 | 30 | 25 | – | – | – | – | – | – | – | – | – | 40 | 35 | 30 |
| 2 | 35 | 30 | 25 | – | – | – | – | – | – | – | – | – | 40 | 35 | 30 | |
| 3 | 45 | 35 | 25 | – | – | – | – | – | – | – | – | – | 50 | 40 | 30 | |
| 4 | 50 | 45 | 30 | – | – | – | 50 | 45 | 35 | – | – | – | 55 | 50 | 35 | |
| H | 1 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. | ||||||||||||||||
Recommended Starting Speeds and Feeds [SFM]
| KSSM8+™ • IC10 • Recommended Starting Speed [SFM] | ||||||||||||||||
| Calidad | KC725M | KCK15 | KCPK30 | KCK20B | KCPM40 | |||||||||||
| Chip Thickness hex Inch | Mín | Máx. | Mín | Máx. | Mín | Máx. | Mín | Máx. | Mín | Máx. | ||||||
| Grupo de materiales | Máx. | Inicio | Mín | Máx. | Inicio | Mín | Máx. | Inicio | Mín | Máx. | Inicio | Mín | Máx. | Inicio | Mín | |
| P | 1 | 260 | 230 | 215 | – | – | – | 455 | 395 | 370 | – | – | – | 295 | 260 | 245 |
| 2 | 220 | 190 | 160 | – | – | – | 280 | 255 | 230 | – | – | – | 250 | 215 | 180 | |
| 3 | 200 | 170 | 140 | – | – | – | 255 | 230 | 205 | – | – | – | 230 | 195 | 160 | |
| 4 | 180 | 150 | 120 | – | – | – | 225 | 185 | 160 | – | – | – | 205 | 170 | 135 | |
| 5 | 150 | 135 | 120 | – | – | – | 190 | 170 | 150 | – | – | – | 170 | 155 | 135 | |
| 6 | 130 | 100 | 80 | – | – | – | 160 | 135 | 110 | – | – | – | 150 | 115 | 90 | |
| M | 1 | 170 | 150 | 135 | – | – | – | 205 | 185 | 155 | – | – | – | 195 | 170 | 155 |
| 2 | 155 | 130 | 110 | – | – | – | 185 | 160 | 140 | – | – | – | 175 | 150 | 125 | |
| 3 | 115 | 100 | 80 | – | – | – | 145 | 130 | 115 | – | – | – | 130 | 115 | 90 | |
| K | 1 | – | – | – | 420 | 385 | 340 | 295 | 265 | 240 | 360 | 290 | 245 | – | – | – |
| 2 | – | – | – | 335 | 295 | 275 | 235 | 210 | 190 | 280 | 230 | 195 | – | – | – | |
| 3 | – | – | – | 280 | 250 | 230 | 195 | 175 | 160 | 210 | 175 | 140 | – | – | – | |
| N | 1 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| 2 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| 3 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| S | 1 | 35 | 30 | 25 | – | – | – | – | – | – | – | – | – | 40 | 35 | 30 |
| 2 | 35 | 30 | 25 | – | – | – | – | – | – | – | – | – | 40 | 35 | 30 | |
| 3 | 45 | 35 | 25 | – | – | – | – | – | – | – | – | – | 50 | 40 | 30 | |
| 4 | 50 | 45 | 30 | – | – | – | 50 | 45 | 35 | – | – | – | 55 | 50 | 35 | |
| H | 1 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – |
| As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining. | ||||||||||||||||