정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
DFR 4xD Flanged Shk Holemaking - 3022345 - Kennametal
DFR 4xD SSF 섕크
Drill FIX DFR 드릴 바디
제품 번호3022345
ISO 카탈로그 IDDFR0703R4SSF100ANSI 카탈로그 IDDFR0703R4SSF100
정가
$597.56/개당
할인
가격
/개당
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
- P Steel
- M Stainless Steel
- K Cast Iron
- N Non-Ferrous
- S High-Temp Alloys
드릴링
드릴링: 경사 진입면
드릴링: 경사 출구면
드릴링: X 오프셋
드릴링: 볼록면
섕크 — 원통형 플랫 및 플랜지 타입
내부 쿨런트: 반경방향: 인덱서블 드릴링
드릴링: 막힌 홀
Chain Drilling
Drilling: Cross-Hole Drilling
Drilling: Half-Cylindrical Drilling
Drilling: Corner Drilling 45°
Sending to {{cadTool}} in progress...
Downloaded file will be available after import in the {{cadTool}} tool library.
MetricInch
| 제품 번호 | 3022345 |
| ISO 카탈로그 ID | DFR0703R4SSF100 |
| ANSI 카탈로그 ID | DFR0703R4SSF100 |
| [D] Adapter / Shank / Bore Diameter | 25.4 mm |
| [D] Adapter / Shank / Bore Diameter | 1 in |
| [D1] Drill Diameter M | 17.856 mm |
| [D1] Drill Diameter M | .703 in |
| [D1MAX] Drill Diameter Maximum | 18.857 mm |
| [D1MAX] Drill Diameter Maximum | .7424 in |
| [L1] Insert Gage Length | 97.272 mm |
| [L1] Insert Gage Length | 3.829 in |
| [L4] Maximum Drilling Depth | 71.425 mm |
| [L4] Maximum Drilling Depth | 2.812 in |
| [L5] Drill Point Length | 0.618 mm |
| [L5] Drill Point Length | .0243 in |
| [LS] Shank Length | 76.2 mm |
| [LS] Shank Length | 3 in |
| Gage Insert | DFR0302. |
공작물 재료
- Steel
- Stainless Steel
- Cast Iron
- Non-Ferrous
- High-Temp Alloys
사용 및 응용 분야
특징 및 장점
- Drill Fix DFR with rectangular-shaped inserts offer highest stability and feed rates at smaller sizes.
- X-offset design to adjust diameter size on turning machines and optimize tolerances on machining centers.
- Drill shipped with insert screws, side pipe plug, and Torx wrench.
이송 및 속도를 계산하려면 솔루션을 생성하세요.
솔루션 생성 후 이송 및 속도 아이콘을 선택하면 추천 값이 제공됩니다. 기계와 사양을 추가하여 사용자 정보를 지정하거나 슬라이더를 사용하여 조정할 수 있습니다.
Warning
경고 • Drill Fix DFR
| WARNING During through-hole operations, a slug or disc is produced as the tool breaks through the workpiece. When the drill is stationary and the workpiece is rotating, this slug may be hurled from the chuck by centrifugal force. Provide adequate shielding to protect bystanders. |
자세히 읽기View Less
Dimension
Dimensions • DFR 플랜지 섕크
| D | LS |
| 20 | 50 |
자세히 읽기View Less
애플리케이션 데이터
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500–.625" | DFR03... .688–.750" | DFR04... .813–1.00" | ||||||
| P | 1 | S | O | MD | KCU25 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | GD | KCPK10 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| 3 | S | O | GD | KCPK10 | 853 | 935 | 1050 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 590 | 640 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 361 | 394 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| 4 | S | O | GD | KCU25 | 722 | 820 | 984 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 492 | 590 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 295 | 361 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| 5 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .003–.005 | .004–.006 | .004–.007 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .003–.005 | .004–.006 | .004–.007 | ||
| I | LD | KC7140 | ||||||||||
| 6 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| I | LD | KC7140 | ||||||||||
| U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .004–.006 | .004–.007 | .006–.010 | ||
| I | LD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| P | 1 | S | O | MD | KCU25 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 |
| 1 | S | I | MD | KC7140 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | U | O | MD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | U | I | MD | KC7140 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 1 | I | I | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | S | O | GD | KCPK10 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | S | I | LD | KC7140 | 1017 | 1066 | 1181 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | U | O | GD | KCU40 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | U | I | LD | KC7140 | 656 | 705 | 754 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | I | O | MD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 2 | I | I | LD | KC7140 | 426 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | S | O | GD | KCPK10 | 853 | 935 | 1050 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | S | I | LD | KC7140 | 853 | 935 | 1050 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | U | O | GD | KCU40 | 590 | 640 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | U | I | LD | KC7140 | 590 | 640 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | I | O | GD | KC7140 | 361 | 394 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 3 | I | I | LD | KC7140 | 361 | 394 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | S | O | GD | KCU25 | 722 | 820 | 984 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | S | I | LD | KC7140 | 722 | 820 | 984 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | U | O | GD | KCU40 | 492 | 590 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | U | I | LD | KC7140 | 492 | 590 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | I | O | GD | KC7140 | 295 | 361 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 4 | I | I | LD | KC7140 | 295 | 361 | 459 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 5 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | S | I | LD | KC7140 | 590 | 656 | 722 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | U | I | LD | KC7140 | 394 | 443 | 492 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 5 | I | I | LD | KC7140 | 230 | 279 | 328 | SFM | .003–.005 | .004–.006 | .004–.007 | |
| 6 | S | O | GD | KCU25 | 590 | 656 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | S | I | LD | KC7140 | 590 | 656 | 722 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | U | O | GD | KCU40 | 394 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | U | I | LD | KC7140 | 394 | 443 | 492 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | I | O | GD | KC7140 | 230 | 279 | 328 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| 6 | I | I | LD | KC7140 | 230 | 279 | 328 | SFM | .004–.006 | .004–.007 | .006–.010 | |
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500–.625" | DFR03... .688–.750" | DFR04... .813–1.00" | ||||||
| M | 1 | S | O | MD | KC7140 | 492 | 623 | 754 | SFM | .003–.005 | .003–.006 | .004–.007 |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | MD | KC7140 | 492 | 590 | 689 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| 3 | S | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| I | MD | KC7140 | ||||||||||
| U | O | MD | KC7140 | 262 | 361 | 459 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 164 | 230 | 295 | SFM | .003–.005 | .003–.006 | .004–.007 | ||
| I | MD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| M | 1 | S | O | MD | KC7140 | 492 | 623 | 754 | SFM | .003–.005 | .003–.006 | .004–.007 |
| 1 | S | I | MD | KC7140 | 492 | 623 | 754 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | U | I | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 1 | I | I | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | S | O | MD | KC7140 | 492 | 590 | 689 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | S | I | MD | KC7140 | 492 | 590 | 689 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | U | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | U | I | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | I | O | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 2 | I | I | MD | KC7140 | 197 | 262 | 328 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | S | O | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | S | I | MD | KC7140 | 328 | 426 | 525 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | U | O | MD | KC7140 | 262 | 361 | 459 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | U | I | MD | KC7140 | 262 | 361 | 459 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | I | O | MD | KC7140 | 164 | 230 | 295 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| 3 | I | I | MD | KC7140 | 164 | 230 | 295 | SFM | .003–.005 | .003–.006 | .004–.007 | |
| Inch | ||||||||||||
| Material | Pocket Seat | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500–.625" | DFR03... .688–.750" | DFR04... .813–1.00" | ||||||
| K | 1 | S | O | GD | KCPK10 | 656 | 787 | 984 | SFM | .004–.007 | .005–.008 | .006–.009 |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 394 | 508 | 656 | SFM | .004–.007 | .005–.008 | .006–.009 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 262 | 328 | 410 | SFM | .004–.007 | .005–.008 | .005–.009 | ||
| I | LD | KC7140 | ||||||||||
| 2 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .005–.009 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .006–.009 | ||
| I | LD | KC7140 | ||||||||||
| 3 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .006–.009 | ||
| I | LD | KC7140 | ||||||||||
| I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .005–.009 | ||
| I | LD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| K | 1 | S | O | GD | KCPK10 | 656 | 787 | 984 | SFM | .004–.007 | .005–.008 | .006–.009 |
| 1 | S | I | LD | KCU40 | 656 | 787 | 984 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 1 | U | O | GD | KCU25 | 394 | 508 | 656 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 1 | U | I | LD | KC7140 | 394 | 508 | 656 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 1 | I | O | GD | KCU40 | 262 | 328 | 410 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 1 | I | I | LD | KC7140 | 262 | 328 | 410 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 2 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 2 | S | I | LD | KCU40 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 2 | U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 2 | U | I | LD | KC7140 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 2 | I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 2 | I | I | LD | KC7140 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 3 | S | O | GD | KCPK10 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 3 | S | I | LD | KCU40 | 590 | 722 | 853 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 3 | U | O | GD | KCU25 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 3 | U | I | LD | KC7140 | 361 | 459 | 558 | SFM | .004–.007 | .005–.008 | .006–.009 | |
| 3 | I | O | GD | KCU40 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| 3 | I | I | LD | KC7140 | 262 | 328 | 394 | SFM | .004–.007 | .005–.008 | .005–.009 | |
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | ||||||
| N | 1 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 984 | 1312 | 1640 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 2 | S | O | ST | KD1425 | 1230 | 1804 | 2542 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 574 | 820 | 1066 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 3 | S | O | ST | KD1425 | 1148 | 1640 | 2132 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 492 | 820 | 1148 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 4 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | LD | KCU40 | 820 | 1148 | 1486 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | LD | KCU40 | ||||||||||
| 5 | S | O | HP | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | HP | KD1425 | ||||||||||
| U | O | HP | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | HP | KCU40 | ||||||||||
| I | O | HP | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | HP | KCU40 | ||||||||||
| 6 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| I | ST | KD1425 | ||||||||||
| U | O | GD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | GD | KCU40 | ||||||||||
| I | O | GD | KMF | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | ||
| I | GD | KMF | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"–.625" | DFR03... .688"–.750" | DFR04... .813"–1.00" | |
| N | 1 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 |
| 1 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | U | O | LD | KCU40 | 984 | 1312 | 1640 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | U | I | LD | KCU40 | 984 | 1312 | 1640 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 1 | I | I | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | S | O | ST | KD1425 | 1230 | 1804 | 2542 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | S | I | ST | KD1425 | 1230 | 1804 | 2542 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | U | I | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | I | O | LD | KCU40 | 574 | 820 | 1066 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 2 | I | I | LD | KCU40 | 574 | 820 | 1066 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | S | O | ST | KD1425 | 1148 | 1640 | 2132 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | S | I | ST | KD1425 | 1148 | 1640 | 2132 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | U | I | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | I | O | LD | KCU40 | 492 | 820 | 1148 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 3 | I | I | LD | KCU40 | 492 | 820 | 1148 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | U | O | LD | KCU40 | 820 | 1148 | 1486 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | U | I | LD | KCU40 | 820 | 1148 | 1486 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | I | O | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 4 | I | I | LD | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | S | O | HP | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | S | I | HP | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | U | O | HP | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | U | I | HP | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | I | O | HP | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 5 | I | I | HP | KCU40 | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | U | O | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | U | I | LD | KCU40 | 820 | 1148 | 1476 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | I | O | LD | KMF | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| 6 | I | I | LD | KMF | 656 | 984 | 1312 | SFM | .003–.004 | .004–.006 | .005–.006 | |
| Inch | ||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||||
| Range | ||||||||||||
| Min | Starting Value | Max | Ø | DFR02... .500 | DFR03... .688 | DFR04... .813 | ||||||
| S | 1 | S | O | GD | KCU40 | 197 | 230 | 246 | SFM | .002–.002 | .002–.003 | .002–.004 |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 131 | 164 | 197 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| 2 | S | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 98 | 131 | 164 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| 3 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.004 | .002–.003 | .002–.004 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| 4 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| I | LD | KCU40 | ||||||||||
| U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | LD | KC7140 | ||||||||||
| I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | ||
| I | MD | KC7140 | ||||||||||
| Inch | ||||||||||||
| Cutting Speed | ||||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR02... .500"-.625" | DFR03... .688"-.750" | DFR04... .813"-1.00" | |
| S | 1 | S | O | GD | KCU40 | 197 | 230 | 246 | SFM | .002–.002 | .002–.003 | .002–.004 |
| 1 | S | I | LD | KCU40 | 197 | 230 | 246 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | U | O | GD | KCU40 | 131 | 164 | 197 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | U | I | LD | KC7140 | 131 | 164 | 197 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 1 | I | I | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | S | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | S | I | LD | KCU40 | 164 | 197 | 230 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | U | O | GD | KCU40 | 98 | 131 | 164 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | U | I | LD | KC7140 | 98 | 131 | 164 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | I | O | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 2 | I | I | MD | KC7140 | 82 | 98 | 131 | SFM | .002–.002 | .002–.003 | .002–.004 | |
| 3 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.004 | .002–.003 | .002–.004 | |
| 3 | S | I | LD | KCU40 | 230 | 262 | 295 | SFM | .002–.004 | .002–.003 | .002–.004 | |
| 3 | U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 3 | U | I | LD | KC7140 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 3 | I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 3 | I | I | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | S | O | GD | KCU40 | 230 | 262 | 295 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | S | I | LD | KCU40 | 230 | 262 | 295 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | U | O | GD | KCU40 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | U | I | LD | KC7140 | 164 | 197 | 230 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | I | O | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
| 4 | I | I | MD | KC7140 | 98 | 131 | 164 | SFM | .002–.003 | .002–.004 | .002–.004 | |
DFR™ • PCD • Inch
| Metric | ||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||
| Range | ||||||||||
| Min | Starting Value | Max | Ø | DFR04 20,50–24,00mm | ||||||
| N | 1 | S | O | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 |
| I | ST | KD1425 | ||||||||
| 2 | S | O | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 3 | S | O | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 4 | S | O | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| I | ST | KD1425 | ||||||||
| 5 | S | O | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
| I | ST | KD1425 | ||||||||
| Inch | ||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (fz) by Diameter | ||||
| Range | ||||||||||
| Min | Starting Value | Max | Ø | DFR04 .813–1.00" | ||||||
| N | 1 | S | O | ST | KD1425 | 1300 | 2362 | 2760 | IPR | .002–.003 |
| I | ST | KD1425 | ||||||||
| 2 | S | O | ST | KD1425 | 1209 | 2197 | 2567 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 3 | S | O | ST | KD1425 | 1118 | 2032 | 2374 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 4 | S | O | ST | KD1425 | 1560 | 2362 | 2760 | IPR | .005–.007 | |
| I | ST | KD1425 | ||||||||
| 5 | S | O | ST | KD1425 | 1575 | 2362 | 2834 | IPR | .002–.003 | |
| I | ST | KD1425 | ||||||||
| Metric | ||||||||||
| Cutting Speed | ||||||||||
| Range | Recommended Feed Rate (fz) by Diameter | |||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFR04 20,50–24,00 mm | |
| N | 1 | S | O | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 |
| 1 | S | I | ST | KD1425 | 396 | 720 | 841 | mm/r | 0,06–0,08 | |
| 2 | S | O | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| 2 | S | I | ST | KD1425 | 369 | 670 | 782 | mm/r | 0,12–0,18 | |
| 3 | S | O | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| 3 | S | I | ST | KD1425 | 341 | 619 | 723 | mm/r | 0,12–0,18 | |
| 4 | S | O | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| 4 | S | I | ST | KD1425 | 475 | 720 | 841 | mm/r | 0,12–0,18 | |
| 5 | S | O | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
| 5 | S | I | ST | KD1425 | 480 | 720 | 864 | mm/r | 0,06–0,08 | |
자세히 읽기View Less
I have read and accepted the Terms & Conditions of use
완벽하게 호환되는 공구를 찾으려면 솔루션을 생성하세요.
상품명
제품 번호
ISO 카탈로그 ID
ANSI 카탈로그 ID
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
완벽하게 호환되는 공구를 찾으려면 솔루션을 생성하세요.
상품명
제품 번호
ISO 카탈로그 ID
ANSI 카탈로그 ID
재종
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
상품명
제품 번호
ISO 카탈로그 ID
ANSI 카탈로그 ID
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간