정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
DFT 2.5xD Flanged Shk Inch RH Holemaking - 1527626 - Kennametal
DFT 2.5xD 플랜지 섕크(우승수)
Drill FIX DFT 바디
제품 번호1527626
ISO 카탈로그 IDDFT0703R2SSF075ANSI 카탈로그 IDDFT0703R2SSF075
정가
$590.58/개당
할인
가격
/개당
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
- P Steel
- M Stainless Steel
- K Cast Iron
- N Non-Ferrous
- S High-Temp Alloys
드릴링
드릴링: 경사 진입면
드릴링: 경사 출구면
드릴링: X 오프셋
드릴링: 볼록면
섕크 — 원통형 플랫 및 플랜지 타입
내부 쿨런트: 반경방향: 인덱서블 드릴링
드릴링: 막힌 홀
Chain Drilling
Drilling: Cross-Hole Drilling
Drilling: Half-Cylindrical Drilling
Drilling: Corner Drilling 45°
Sending to {{cadTool}} in progress...
Downloaded file will be available after import in the {{cadTool}} tool library.
MetricInch
| 제품 번호 | 1527626 |
| ISO 카탈로그 ID | DFT0703R2SSF075 |
| ANSI 카탈로그 ID | DFT0703R2SSF075 |
| [D] Adapter / Shank / Bore Diameter | 19.05 mm |
| [D] Adapter / Shank / Bore Diameter | .75 in |
| [D1] Drill Diameter M | 17.844 mm |
| [D1] Drill Diameter M | .7025 in |
| [D1MAX] Drill Diameter Maximum | 21.653 mm |
| [D1MAX] Drill Diameter Maximum | .8525 in |
| [L1] Insert Gage Length | 76.2 mm |
| [L1] Insert Gage Length | 3 in |
| [L4] Maximum Drilling Depth | 44.704 mm |
| [L4] Maximum Drilling Depth | 1.76 in |
| [L5] Drill Point Length | 0.439 mm |
| [L5] Drill Point Length | .0173 in |
| [LS] Shank Length | 50.8 mm |
| [LS] Shank Length | 2 in |
| Gage Insert | DFT0302. |
공작물 재료
- Steel
- Stainless Steel
- Cast Iron
- Non-Ferrous
- High-Temp Alloys
사용 및 응용 분야
특징 및 장점
- Drill Fix DFT is one of the most versatile and reliable tool solutions covering a large diameter range and offers portfolio of insert geometries and grades.
- Trigon shaped inserts are used for both inboard and outboard inserts and offer the highest centering capabilities and three cutting edges each.
- Drill shipped with insert screws, side pipe plug, and Torx wrench.
이송 및 속도를 계산하려면 솔루션을 생성하세요.
솔루션 생성 후 이송 및 속도 아이콘을 선택하면 추천 값이 제공됩니다. 기계와 사양을 추가하여 사용자 정보를 지정하거나 슬라이더를 사용하여 조정할 수 있습니다.
Warning
경고 • Drill Fix DFR
| WARNING During through-hole operations, a slug or disc is produced as the tool breaks through the workpiece. When the drill is stationary and the workpiece is rotating, this slug may be hurled from the chuck by centrifugal force. Provide adequate shielding to protect bystanders. |
자세히 읽기View Less
Dimension
 | ||||
| D | LS | CF | CS | pipe plug |
| 0.750 | 2.00 | 1/8-27 NPT | R 1/8-27 NPT | 1025612 |
| 1.000 | 3.00 | 1/8-27 NPT | R 1/4-18 NPT | 1025612 |
| 1.250 | 3.25 | 1/8-27 NPT | R 1/4-18 NPT | 1025612 |
| 1.500 | 3.75 | 1/8-27 NPT | R 1/4-18 NPT | 1025612 |
| 2.000 | 4.00 | 1/8-27 NPT | R 1/4-18 NPT | 1025612 |
자세히 읽기View Less
애플리케이션 데이터
| Inch | |||||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (f) by Diameter | |||||||||
| Range | |||||||||||||||
| Min | Starting Value | Max | Ø | DFT03... .625"–.969" | DFT05... .984"–1.250" | DFT06... 1.313"–1.563" | DFT07... 1.625"–1.875" | DFT09... 1.938"–2.125" | DFT011... 2.750"–3.250" | ||||||
| P | 1 | S | O | MD | KCU25 | 1017 | 1066 | 1181 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 |
| I | MD | KC7140 | |||||||||||||
| U | O | MD | KCU25 | 656 | 705 | 754 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | ||
| I | MD | KC7140 | |||||||||||||
| I | O | MD | KCU40 | 426 | 443 | 492 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | ||
| I | MD | KC7140 | |||||||||||||
| 2 | S | O | HP | KCPK10 | 1017 | 1066 | 1181 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| I | HP | KC7140 | |||||||||||||
| U | O | HP | KCU25 | 656 | 705 | 754 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | HP | KCU40 | 426 | 443 | 492 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | ||
| I | HP | KC7140 | |||||||||||||
| 3 | S | O | HP | KCPK10 | 853 | 935 | 1050 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| I | HP | KC7140 | |||||||||||||
| U | O | HP | KCU25 | 590 | 640 | 722 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | HP | KCU40 | 361 | 394 | 459 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | ||
| I | HP | KC7140 | |||||||||||||
| 4 | S | O | HP | KCU25 | 722 | 820 | 984 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| I | HP | KC7140 | |||||||||||||
| U | O | HP | KCU40 | 492 | 590 | 722 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | HP | KC7140 | 295 | 361 | 459 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | ||
| I | HP | KC7140 | |||||||||||||
| 5 | S | O | HP | KCU25 | 590 | 656 | 722 | IPR | .002–.004 | .003–.005 | .004–.006 | .004–.007 | .005–.009 | .005–.009 | |
| I | HP | KC7140 | |||||||||||||
| U | O | HP | KCU40 | 394 | 443 | 492 | IPR | .002–.004 | .003–.005 | .004–.006 | .004–.007 | .005–.009 | .005–.009 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | HP | KC7140 | 230 | 279 | 328 | IPR | .002–.004 | .003–.005 | .004–.006 | .004–.007 | .005–.009 | .005–.009 | ||
| I | HP | KC7140 | |||||||||||||
| 6 | S | O | HP | KCU25 | 590 | 656 | 722 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| I | HP | KC7140 | |||||||||||||
| U | O | HP | KCU40 | 394 | 443 | 492 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | HP | KC7140 | 230 | 279 | 328 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | ||
| I | HP | KC7140 | |||||||||||||
| Inch | |||||||||||||||
| Cutting Speed | |||||||||||||||
| Range | Recommended Feed Rate (f) by Diameter | ||||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFT03... .625"–.969" | DFT05... .984"–1.250" | DFT06... 1.313"–1.563" | DFT07... 1.625"–1.875" | DFT09... 1.938"–2.125" | DFT011... 2.750"–3.250" | |
| P | 1 | S | O | MD | KCU25 | 1017 | 1066 | 1181 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 |
| 1 | S | I | MD | KC7140 | 1017 | 1066 | 1181 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 1 | U | O | MD | KCU25 | 656 | 705 | 754 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 1 | U | I | MD | KC7140 | 656 | 705 | 754 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 1 | I | O | MD | KCU40 | 426 | 443 | 492 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 1 | I | I | MD | KC7140 | 426 | 443 | 492 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 2 | S | O | HP | KCPK10 | 1017 | 1066 | 1181 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 2 | S | I | HP | KC7140 | 1017 | 1066 | 1181 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 2 | U | O | HP | KCU25 | 656 | 705 | 754 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 2 | U | I | HP | KC7140 | 656 | 705 | 754 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 2 | I | O | HP | KCU40 | 426 | 443 | 492 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 2 | I | I | HP | KC7140 | 426 | 443 | 492 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 3 | S | O | HP | KCPK10 | 853 | 935 | 1050 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 3 | S | I | HP | KC7140 | 853 | 935 | 1050 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 3 | U | O | HP | KCU25 | 590 | 640 | 722 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 3 | U | I | HP | KC7140 | 590 | 640 | 722 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 3 | I | O | HP | KCU40 | 361 | 394 | 459 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 3 | I | I | HP | KC7140 | 361 | 394 | 459 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 4 | S | O | HP | KCU25 | 722 | 820 | 984 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 4 | S | I | HP | KC7140 | 722 | 820 | 984 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 4 | U | O | HP | KCU40 | 492 | 590 | 722 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 4 | U | I | HP | KC7140 | 492 | 590 | 722 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 4 | I | O | HP | KC7140 | 295 | 361 | 459 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 4 | I | I | HP | KC7140 | 295 | 361 | 459 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 5 | S | O | HP | KCU25 | 590 | 656 | 722 | IPR | .002–.004 | .003–.005 | .004–.006 | .004–.007 | .005–.009 | .005–.009 | |
| 5 | S | I | HP | KC7140 | 590 | 656 | 722 | IPR | .002–.004 | .003–.005 | .004–.006 | .004–.007 | .005–.009 | .005–.009 | |
| 5 | U | O | HP | KCU40 | 394 | 443 | 492 | IPR | .002–.004 | .003–.005 | .004–.006 | .004–.007 | .005–.009 | .005–.009 | |
| 5 | U | I | HP | KC7140 | 394 | 443 | 492 | IPR | .002–.004 | .003–.005 | .004–.006 | .004–.007 | .005–.009 | .005–.009 | |
| 5 | I | O | HP | KC7140 | 230 | 279 | 328 | IPR | .002–.004 | .003–.005 | .004–.006 | .004–.007 | .005–.009 | .005–.009 | |
| 5 | I | I | HP | KC7140 | 230 | 279 | 328 | IPR | .002–.004 | .003–.005 | .004–.006 | .004–.007 | .005–.009 | .005–.009 | |
| 6 | S | O | HP | KCU25 | 590 | 656 | 722 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 6 | S | I | HP | KC7140 | 590 | 656 | 722 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 6 | U | O | HP | KCU40 | 394 | 443 | 492 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 6 | U | I | HP | KC7140 | 394 | 443 | 492 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 6 | I | O | HP | KC7140 | 230 | 279 | 328 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| 6 | I | I | HP | KC7140 | 230 | 279 | 328 | IPR | .002–.004 | .004–.006 | .004–.007 | .006–.010 | .007–.012 | .007–.012 | |
| Inch | |||||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (f) by Diameter | |||||||||
| Range | |||||||||||||||
| Min | Starting Value | Max | Ø | DFT03... .625"–.969" | DFT05... .984"–1.250" | DFT06... 1.313"–1.563" | DFT07... 1.625"–1.875" | DFT09... 1.938"–2.125" | DFT011... 2.750"–3.250" | ||||||
| M | 1 | S | O | MD | KC7140 | 492 | 623 | 754 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 |
| I | MD | KC7140 | |||||||||||||
| U | O | MD | KC7140 | 328 | 426 | 525 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | ||
| I | MD | KC7140 | |||||||||||||
| I | O | MD | KC7140 | 197 | 262 | 328 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | ||
| I | MD | KC7140 | |||||||||||||
| 2 | S | O | MD | KC7140 | 492 | 590 | 689 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| I | MD | KC7140 | |||||||||||||
| U | O | MD | KC7140 | 328 | 426 | 525 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | ||
| I | MD | KC7140 | |||||||||||||
| I | O | MD | KC7140 | 197 | 262 | 328 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | ||
| I | MD | KC7140 | |||||||||||||
| 3 | S | O | MD | KC7140 | 328 | 426 | 525 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| I | MD | KC7140 | |||||||||||||
| U | O | MD | KC7140 | 262 | 361 | 459 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | ||
| I | MD | KC7140 | |||||||||||||
| I | O | MD | KC7140 | 164 | 230 | 295 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | ||
| I | MD | KC7140 | |||||||||||||
| Inch | |||||||||||||||
| Cutting Speed | |||||||||||||||
| Range | Recommended Feed Rate (f) by Diameter | ||||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFT03... .625"–.969" | DFT05... .984"–1.250" | DFT06... 1.313"–1.563" | DFT07... 1.625"–1.875" | DFT09... 1.938"–2.125" | DFT011... 2.750"–3.250" | |
| M | 1 | S | O | MD | KC7140 | 492 | 623 | 754 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 |
| 1 | S | I | MD | KC7140 | 492 | 623 | 754 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 1 | U | O | MD | KC7140 | 328 | 426 | 525 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 1 | U | I | MD | KC7140 | 328 | 426 | 525 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 1 | I | O | MD | KC7140 | 197 | 262 | 328 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 1 | I | I | MD | KC7140 | 197 | 262 | 328 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 2 | S | O | MD | KC7140 | 492 | 590 | 689 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 2 | S | I | MD | KC7140 | 492 | 590 | 689 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 2 | U | O | MD | KC7140 | 328 | 426 | 525 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 2 | U | I | MD | KC7140 | 328 | 426 | 525 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 2 | I | O | MD | KC7140 | 197 | 262 | 328 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 2 | I | I | MD | KC7140 | 197 | 262 | 328 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 3 | S | O | MD | KC7140 | 328 | 426 | 525 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 3 | S | I | MD | KC7140 | 328 | 426 | 525 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 3 | U | O | MD | KC7140 | 262 | 361 | 459 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 3 | U | I | MD | KC7140 | 262 | 361 | 459 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 3 | I | O | MD | KC7140 | 164 | 230 | 295 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| 3 | I | I | MD | KC7140 | 164 | 230 | 295 | IPR | .002–.004 | .003–.005 | .003–.006 | .004–.007 | .004–.008 | .004–.008 | |
| Inch | |||||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (f) by Diameter | |||||||||
| Range | |||||||||||||||
| Min | Starting Value | Max | Ø | DFT03... .625"–.969" | DFT05... .984"–1.250" | DFT06... 1.313"–1.563" | DFT07... 1.625"–1.875" | DFT09... 1.938"–2.125" | DFT011... 2.750"–3.250" | ||||||
| K | 1 | S | O | HP | KCPK10 | 656 | 787 | 984 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 |
| I | HP | KCU40 | |||||||||||||
| U | O | HP | KCU25 | 394 | 508 | 656 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | HP | KCU40 | 262 | 328 | 410 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | ||
| I | HP | KC7140 | |||||||||||||
| 2 | S | O | HP | KCPK10 | 590 | 722 | 853 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| I | HP | KCU40 | |||||||||||||
| U | O | HP | KCU25 | 361 | 459 | 558 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | HP | KCU40 | 262 | 328 | 394 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | ||
| I | HP | KC7140 | |||||||||||||
| 3 | S | O | HP | KCPK10 | 590 | 722 | 853 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| I | HP | KCU40 | |||||||||||||
| U | O | HP | KCU25 | 361 | 459 | 558 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | HP | KCU40 | 262 | 328 | 394 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | ||
| I | HP | KC7140 | |||||||||||||
| Inch | |||||||||||||||
| Cutting Speed | |||||||||||||||
| Range | Recommended Feed Rate (f) by Diameter | ||||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFT03... .625"–.969" | DFT05... .984"–1.250" | DFT06... 1.313"–1.563" | DFT07... 1.625"–1.875" | DFT09... 1.938"–2.125" | DFT011... 2.750"–3.250" | |
| K | 1 | S | O | HP | KCPK10 | 656 | 787 | 984 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 |
| 1 | S | I | HP | KCU40 | 656 | 787 | 984 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 1 | U | O | HP | KCU25 | 394 | 508 | 656 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 1 | U | I | HP | KC7140 | 394 | 508 | 656 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 1 | I | O | HP | KCU40 | 262 | 328 | 410 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 1 | I | I | HP | KC7140 | 262 | 328 | 410 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 2 | S | O | HP | KCPK10 | 590 | 722 | 853 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 2 | S | I | HP | KCU40 | 590 | 722 | 853 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 2 | U | O | HP | KCU25 | 361 | 459 | 558 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 2 | U | I | HP | KC7140 | 361 | 459 | 558 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 2 | I | O | HP | KCU40 | 262 | 328 | 394 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 2 | I | I | HP | KC7140 | 262 | 328 | 394 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 3 | S | O | HP | KCPK10 | 590 | 722 | 853 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 3 | S | I | HP | KCU40 | 590 | 722 | 853 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 3 | U | O | HP | KCU25 | 361 | 459 | 558 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 3 | U | I | HP | KC7140 | 361 | 459 | 558 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 3 | I | O | HP | KCU40 | 262 | 328 | 394 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| 3 | I | I | HP | KC7140 | 262 | 328 | 394 | IPR | .003–.005 | .004–.007 | .006–.010 | .007–.013 | .008–.015 | .008–.015 | |
| Inch | |||||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (f) by Diameter | |||||||||
| Range | |||||||||||||||
| Min | Starting Value | Max | Ø | DFT03... .625"–.969" | DFT05... .984"–1.250" | DFT06... 1.313"–1.563" | DFT07... 1.625"–1.875" | DFT09... 1.938"–2.125" | DFT011... 2.750"–3.250" | ||||||
| N | 1 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 |
| I | ST | KD1425 | |||||||||||||
| U | O | HP | KCU40 | 984 | 1312 | 1640 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | ||
| I | HP | KCU40 | |||||||||||||
| I | O | HP | KMF | 656 | 984 | 1312 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | ||
| I | HP | KMF | |||||||||||||
| 2 | S | O | ST | KD1425 | 1230 | 1804 | 2542 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| I | ST | KD1425 | |||||||||||||
| U | O | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | ||
| I | HP | KCU40 | |||||||||||||
| I | O | HP | KMF | 574 | 820 | 1066 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | ||
| I | HP | KMF | |||||||||||||
| 3 | S | O | ST | KD1425 | 1148 | 1640 | 2132 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| I | ST | KD1425 | |||||||||||||
| U | O | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | ||
| I | HP | KCU40 | |||||||||||||
| I | O | HP | KMF | 492 | 820 | 1148 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | ||
| I | HP | KMF | |||||||||||||
| 4 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| I | ST | KD1425 | |||||||||||||
| U | O | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | ||
| I | HP | KCU40 | |||||||||||||
| I | O | HP | KMF | 656 | 984 | 1312 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | ||
| I | HP | KMF | |||||||||||||
| 5 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| I | ST | KD1425 | |||||||||||||
| U | O | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | ||
| I | HP | KCU40 | |||||||||||||
| I | O | HP | KMF | 656 | 984 | 1312 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | ||
| I | HP | KMF | |||||||||||||
| Inch | |||||||||||||||
| Cutting Speed | |||||||||||||||
| Range | Recommended Feed Rate (f) by Diameter | ||||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFT03... .625"–.969" | DFT05... .984"–1.250" | DFT06... 1.313"–1.563" | DFT07... 1.625"–1.875" | DFT09... 1.938"–2.125" | DFT011... 2.750"–3.250" | |
| N | 1 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 |
| 1 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 1 | U | O | HP | KCU40 | 984 | 1312 | 1640 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 1 | U | I | HP | KCU40 | 984 | 1312 | 1640 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 1 | I | O | HP | KMF | 656 | 984 | 1312 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 1 | I | I | HP | KMF | 656 | 984 | 1312 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 2 | S | O | ST | KD1425 | 1230 | 1804 | 2542 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 2 | S | I | ST | KD1425 | 1230 | 1804 | 2542 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 2 | U | O | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 2 | U | I | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 2 | I | O | HP | KMF | 574 | 820 | 1066 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 2 | I | I | HP | KMF | 574 | 820 | 1066 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 3 | S | O | ST | KD1425 | 1148 | 1640 | 2132 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 3 | S | I | ST | KD1425 | 1148 | 1640 | 2132 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 3 | U | O | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 3 | U | I | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 3 | I | O | HP | KMF | 492 | 820 | 1148 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 3 | I | I | HP | KMF | 492 | 820 | 1148 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 4 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 4 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 4 | U | O | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 4 | U | I | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 4 | I | O | HP | KMF | 656 | 984 | 1312 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 4 | I | I | HP | KMF | 656 | 984 | 1312 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 5 | S | O | ST | KD1425 | 1312 | 1968 | 2624 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 5 | S | I | ST | KD1425 | 1312 | 1968 | 2624 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 5 | U | O | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 5 | U | I | HP | KCU40 | 820 | 1148 | 1476 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 5 | I | O | HP | KMF | 656 | 984 | 1312 | IPR | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| 5 | I | I | HP | KMF | 656 | 984 | 1312 | ipr | .002–.003 | .003–.004 | .004–.006 | .005–.006 | .006–.007 | .006–.007 | |
| Inch | |||||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Cutting Speed | Recommended Feed Rate (f) by Diameter | |||||||||
| Range | |||||||||||||||
| Min | Starting Value | Max | Ø | DFT03... .625"–.969" | DFT05... .984"–1.250" | DFT06... 1.313"–1.563" | DFT07... 1.625"–1.875" | DFT09... 1.938"–2.125" | DFT011... 2.750"–3.250" | ||||||
| S | 1 | S | O | HP | KCU40 | 197 | 230 | 246 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 |
| I | HP | KCU40 | |||||||||||||
| U | O | HP | KCU40 | 131 | 164 | 197 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | MD | KC7140 | 82 | 98 | 131 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | ||
| I | MD | KC7140 | |||||||||||||
| 2 | S | O | HP | KCU40 | 164 | 197 | 230 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| I | HP | KCU40 | |||||||||||||
| U | O | HP | KCU40 | 98 | 131 | 164 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | MD | KC7140 | 82 | 98 | 131 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | ||
| I | MD | KC7140 | |||||||||||||
| 3 | S | O | HP | KCU40 | 230 | 262 | 295 | IPR | .002–.002 | .002–.004 | .002–.003 | .002–.004 | .004–.006 | .004–.006 | |
| I | HP | KCU40 | |||||||||||||
| U | O | HP | KCU40 | 164 | 197 | 230 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | MD | KC7140 | 98 | 131 | 164 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | ||
| I | MD | KC7140 | |||||||||||||
| 4 | S | O | HP | KCU40 | 230 | 262 | 295 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
| I | HP | KCU40 | |||||||||||||
| U | O | HP | KCU40 | 164 | 197 | 230 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | ||
| I | HP | KC7140 | |||||||||||||
| I | O | MD | KC7140 | 98 | 131 | 164 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | ||
| I | MD | KC7140 | |||||||||||||
| Inch | |||||||||||||||
| Cutting Speed | |||||||||||||||
| Range | Recommended Feed Rate (f) by Diameter | ||||||||||||||
| Material | Condition | Pocket Seat | Geometry | Grade | Min | Starting Value | Max | Ø | DFT03... .625"–.969" | DFT05... .984"–1.250" | DFT06... 1.313"–1.563" | DFT07... 1.625"–1.875" | DFT09... 1.938"–2.125" | DFT011... 2.750"–3.250" | |
| S | 1 | S | O | HP | KCU40 | 197 | 230 | 246 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 |
| 1 | S | I | HP | KCU40 | 197 | 230 | 246 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 1 | U | O | HP | KCU40 | 131 | 164 | 197 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 1 | U | I | HP | KC7140 | 131 | 164 | 197 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 1 | I | O | MD | KC7140 | 82 | 98 | 131 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 1 | I | I | MD | KC7140 | 82 | 98 | 131 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 2 | S | O | HP | KCU40 | 164 | 197 | 230 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 2 | S | I | HP | KCU40 | 164 | 197 | 230 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 2 | U | O | HP | KCU40 | 98 | 131 | 164 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 2 | U | I | HP | KC7140 | 98 | 131 | 164 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 2 | I | O | MD | KC7140 | 82 | 98 | 131 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 2 | I | I | MD | KC7140 | 82 | 98 | 131 | IPR | .001–.002 | .002–.002 | .002–.003 | .002–.004 | .003–.005 | .003–.005 | |
| 3 | S | O | HP | KCU40 | 230 | 262 | 295 | IPR | .002–.002 | .002–.004 | .002–.003 | .002–.004 | .004–.006 | .004–.006 | |
| 3 | S | I | HP | KCU40 | 230 | 262 | 295 | IPR | .002–.002 | .002–.004 | .002–.003 | .002–.004 | .004–.006 | .004–.006 | |
| 3 | U | O | HP | KCU40 | 164 | 197 | 230 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
| 3 | U | I | HP | KC7140 | 164 | 197 | 230 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
| 3 | I | O | MD | KC7140 | 98 | 131 | 164 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
| 3 | I | I | MD | KC7140 | 98 | 131 | 164 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
| 4 | S | O | HP | KCU40 | 230 | 262 | 295 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
| 4 | S | I | HP | KCU40 | 230 | 262 | 295 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
| 4 | U | O | HP | KCU40 | 164 | 197 | 230 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
| 4 | U | I | HP | KC7140 | 164 | 197 | 230 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
| 4 | I | O | MD | KC7140 | 98 | 131 | 164 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
| 4 | I | I | MD | KC7140 | 98 | 131 | 164 | IPR | .002–.002 | .002–.003 | .002–.004 | .002–.004 | .004–.006 | .004–.006 | |
자세히 읽기View Less
I have read and accepted the Terms & Conditions of use
완벽하게 호환되는 공구를 찾으려면 솔루션을 생성하세요.
상품명
제품 번호
ISO 카탈로그 ID
ANSI 카탈로그 ID
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
완벽하게 호환되는 공구를 찾으려면 솔루션을 생성하세요.
상품명
제품 번호
ISO 카탈로그 ID
ANSI 카탈로그 ID
재종
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
상품명
제품 번호
ISO 카탈로그 ID
ANSI 카탈로그 ID
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간
정가
/개당
할인
가격
/개당
패키지로 판매 0최소 패키지 크기에 맞게 조정됩니다.
최소 수량: 0패키지 크기 요건을 충족하도록 조정됨.
재고 있음이 제품은 더 이상 사용할 수 없습니다.긴 배송기간