Name: 7792VXP06 Series • End Mill • Screw-On • Metric
SKU: 5681122
Rating: 0 (0 reviews)

인서트 선택

인서트 선택 가이드 • IC 06

7792 Series • IC06 • Insert Selection Guide
소재 그룹	경절삭		범용		중황삭
–	(경절삭용 형상)		–		(중절삭용 형상)
–	내마모성				인성
–	형상	재종	형상	재종	형상	재종
P1-P2	...M41	KCPM40	...D41	SP6519	...D41	X400
P3-P4	...M41	KCPM40	…D	KC522M	…D	KCPM40
P5-P6	...M41	KCPM40	...D41	X500	...D41	X500
M1-M2	...M41	KCSM40	...D41	KCSM40	...D41	KCSM40
M3	...M41	KCSM40	...D41	KCSM40	...D41	KCSM40
K1-K2	…D	KCPK30	…D	KCPK30	…D	KCPK30
K3	…D	KCPK30	…D	KCPK30	…D	KCPK30
N1-N2	–	–	–	–	–	–
N3	–	–	–	–	–	–
S1-S2	...M41	KCSM40	...D41	KCSM40	...D41	KCSM40
S3	...M41	KCSM40	...D41	KCSM40	...D41	KCSM40
S4	...M41	KCSM40	...D41	KCSM40	...D41	KCSM40
H1	…D	KCKP10	…D	KCKP10	…D	KCPM40

자세히 읽기View Less

이송량

권장 초기 이송[mm] • 고이송
인서트 형상	반경 방향 절삭폭(ae) 비율에 따른 권장 초기 날당 이송(Fz)
	DOC	30%			40–100%
	(mm)	L	M	H	L	M	H
.S..D	0,9	0,31	0,62	0,92	0,28	0,56	0,84
.S..D	0,6	0,35	0,70	1,04	0,32	0,64	0,94
.S..D	0,5	0,38	0,75	1,12	0,34	0,69	1,02
.E..D41	0,9	0,17	0,46	0,77	0,16	0,42	0,70
.E..D41	0,6	0,19	0,52	0,87	0,18	0,48	0,79
.E..D41	0,5	0,21	0,56	0,94	0,19	0,52	0,85
.E..M41	0,8	0,17	0,46	0,77	0,16	0,42	0,70
.E..M41	0,6	0,19	0,52	0,87	0,18	0,48	0,79
.E..M41	0,5	0,21	0,56	0,94	0,19	0,52	0,85
L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use Light Machining values as starting feed rate.

7792 Series • IC06 • Recommended Starting Feeds for Plunging [mm/th]
인서트 형상	프로그래밍된 날당 이송(fz)
	L	M	H
.S..D	0,10	0,20	0,30
.E..D41	0,06	0,15	0,25
.E..M41	0,06	0,15	0,25
L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use Light Machining values as starting feed rate.

7792 Series • IC06 • Recommended Starting Feeds for Plunging [IPT]
인서트 형상	프로그래밍된 날당 이송(fz)
	L	M	H
.S..D	0.004	0.008	0.012
.E..D41	0.002	0.006	0.010
.E..M41	0.002	0.006	0.010
L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use Light Machining values as starting feed rate.

권장 초기 이송[mm] • 고이송
인서트 형상	반경 방향 절삭폭(ae) 비율에 따른 권장 초기 날당 이송(Fz)
	DOC	30%			40–100%
	(Inch)	L	M	H	L	M	H
.S..D	0.035	0.012	0.024	0.036	0.011	0.022	0.033
.S..D	0.025	0.014	0.029	0.043	0.013	0.026	0.039
.S..D	0.02	0.016	0.032	0.048	0.015	0.029	0.043
.E..D41	0.035	0.007	0.019	0.031	0.006	0.017	0.028
.E..D41	0.025	0.008	0.022	0.037	0.007	0.020	0.033
.E..D41	0.02	0.009	0.025	0.041	0.008	0.022	0.037
.E..M41	0.031	0.007	0.019	0.031	0.006	0.017	0.028
.E..M41	0.025	0.008	0.022	0.037	0.007	0.020	0.033
.E..M41	0.02	0.009	0.025	0.041	0.008	0.022	0.037
L = Light Machining; M = Medium Machining; H = Heavy Machining NOTE: Use Light Machining values as starting feed rate.

자세히 읽기View Less

속도

권장 초기 속도[m/min]

7792 Series IC06 • Recommended Starting Speed [m/min]
재종		KC510M			KC522M			KCPK30			KCKP10			KCPM40			KCSM40			SP6519			SC6525			X400			X500
칩 두께 hex mm		최소		최대	최소		최대	최소		최대	최소		최대	최소		최대	최소		최대	최소		최대	최소		최대	최소		최대	최소		최대
소재 그룹		최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소
P	1	–	–	–	330	285	270	455	395	370	300	295	260	295	260	245	350	320	300	295	215	130	371	254	142	260	190	120	270	200	130
	2	–	–	–	275	240	200	280	255	230	310	275	240	250	215	180	300	270	220	260	190	115	325	225	121	230	170	105	240	280	115
	3	–	–	–	255	215	175	255	230	205	275	240	205	230	195	160	280	240	195	230	165	100	292	200	104	200	150	95	210	155	100
	4	245	200	170	225	185	150	225	185	160	240	205	160	205	170	135	240	205	165	175	125	75	208	146	79	150	110	70	160	120	75
	5	–	–	–	185	170	150	190	170	150	205	160	125	170	155	135	200	180	160	140	105	70	158	121	79	–	–	–	130	100	70
	6	–	–	–	165	125	100	160	135	110	160	125	110	150	115	90	180	140	100	120	85	50	142	100	58	–	–	–	110	80	50
M	1	–	–	–	205	180	165	205	185	155	–	–	–	195	170	155	260	210	185	270	195	115	192	154	121	–	–	–	250	185	115
	2	–	–	–	185	160	130	185	160	140	–	–	–	175	150	125	235	180	145	235	170	105	258	183	108	–	–	–	220	160	100
	3	–	–	–	140	120	95	145	130	115	–	–	–	130	115	90	175	145	110	195	140	85	208	150	92	–	–	–	180	130	80
K	1	295	265	240	230	205	185	295	265	240	410	330	240	–	–	–	–	–	–	–	–	–	392	271	146	–	–	–	–	–	–
	2	230	205	190	180	160	150	235	210	190	280	245	190	–	–	–	–	–	–	–	–	–	304	208	117	–	–	–	–	–	–
	3	195	175	160	150	135	120	195	175	160	240	195	160	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–
N	1	640	570	525	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–
	2	580	535	490	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–
	3	580	535	490	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–
S	1	–	–	–	40	35	25	–	–	–	–	–	–	40	35	30	50	40	25	55	40	20	–	–	–	–	–	–	45	35	25
	2	–	–	–	40	35	25	–	–	–	–	–	–	40	35	30	55	40	25	45	35	20	–	–	–	–	–	–	45	30	20
	3	–	–	–	50	40	25	–	–	–	–	–	–	50	40	30	65	45	30	55	40	25	–	–	–	–	–	–	50	40	25
	4	–	–	–	50	45	35	50	45	35	–	–	–	55	50	35	75	60	40	80	55	35	–	–	–	–	–	–	60	50	35
H	1	130	105	80	120	90	70	–	–	–	140	110	90	–	–	–	–	–	–	–	–	–	–	–	–	95	70	45	–	–	–
H	2	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	80	60	35	–	–	–
Recommended Starting Speed are pointing to 90° Shoulder Milling . Starting Speed for Face and Copy Milling can be Increased by 20 %. As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining.

7792 Series IC06 • Recommended Starting Speed [SFM]
재종		KC510M			KC522M			KCPK30			KCKP10			KCPM40			KCSM40			SP6519			SC6525			X400			X500
Chip Thickness hex Inch		최소		최대	최소		최대	최소		최대	최소		최대	최소		최대	최소		최대	최소		최대	최소		최대	최소		최대	최소		최대
소재 그룹		최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소	최대	초기값	최소
P	1	–	–	–	1085	935	885	1495	1295	1215	985	970	855	970	855	805	1150	1050	985	970	705	425	1217	833	458	855	625	395	885	655	425
	2	–	–	–	900	785	655	920	835	755	1015	900	785	820	705	590	985	885	720	855	625	375	1067	742	396	755	560	345	785	920	375
	3	–	–	–	835	705	575	835	755	675	900	785	675	755	640	525	920	785	640	755	540	330	950	654	346	655	490	310	690	510	330
	4	805	655	560	740	605	490	740	605	525	785	675	525	675	560	445	785	675	540	575	410	245	692	475	258	490	360	230	525	395	245
	5	–	–	–	605	560	490	625	560	490	675	525	410	560	510	445	655	590	525	460	345	230	525	396	258	–	–	–	425	330	230
	6	–	–	–	540	410	330	525	445	360	525	410	360	490	375	295	590	460	330	395	280	165	458	329	196	–	–	–	360	260	165
M	1	–	–	–	675	590	540	675	605	510	–	–	–	640	560	510	855	690	605	885	640	375	625	508	396	–	–	–	820	605	375
	2	–	–	–	605	525	425	605	525	460	–	–	–	575	490	410	770	590	475	770	560	345	854	604	358	–	–	–	720	525	330
	3	–	–	–	460	395	310	475	425	375	–	–	–	425	375	295	575	475	360	640	460	280	692	492	296	–	–	–	590	425	260
K	1	970	870	785	755	675	605	970	870	785	1345	1085	785	–	–	–	–	–	–	–	–	–	1279	883	475	–	–	–	–	–	–
	2	755	675	625	590	525	490	770	690	625	920	805	625	–	–	–	–	–	–	–	–	–	1000	692	375	–	–	–	–	–	–
	3	640	575	525	490	445	395	640	575	525	785	640	525	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–
N	1	2100	1870	1725	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–
	2	1905	1755	1610	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–
	3	1905	1755	1610	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–
S	1	–	–	–	130	115	80	–	–	–	–	–	–	130	115	100	165	130	80	180	130	65	–	–	–	–	–	–	150	115	80
	2	–	–	–	130	115	80	–	–	–	–	–	–	130	115	100	180	130	80	150	115	65	–	–	–	–	–	–	150	100	65
	3	–	–	–	165	130	80	–	–	–	–	–	–	165	130	100	215	150	100	180	130	80	–	–	–	–	–	–	165	130	80
	4	–	–	–	165	150	115	165	150	115	–	–	–	180	165	115	245	195	130	260	180	115	–	–	–	–	–	–	195	165	115
H	1	425	345	260	395	295	230	–	–	–	460	360	295	–	–	–	–	–	–	–	–	–	–	–	–	310	230	150	–	–	–
H	2	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	–	260	195	115	–	–	–
Recommended Starting Speed are pointing to 90° Shoulder Milling . Starting Speed for Face and Copy Milling can be Increased by 20 %. As the average chip thickness increases, speed should be decreased. Material groups P, M, K and H show recommended starting speeds for dry machining. For wet machining, reduce speed by 20%. Material groups N and S show recommended starting speeds for wet machining. Not recommended for dry machining.

자세히 읽기View Less

애플리케이션 데이터

7792 Series IC06 • Ramping Application Data • Straight-Edged Inserts • Metric
D1 max	램핑 각도 (°)	a_e 최대 플런징	페이싱 피치	DH min [mm] - (min hole diameter)	DH min (최소 홀 직경)
16	7.0°	3	7.6	22	30
20	4.3°	3	11.6	30	38
25	2.6°	3	16.6	42	50
32	1.7°	3	23.6	54	62
35	1.3°	3	23.6	60	68
NOTE: Maximum ramp angle decreases as nose radius increases.

7792 Series IC06 • Ramping Application Data • Curved Edges • Metric
D1 max	램핑 각도 (°)	a_e 최대 플런징	페이싱 피치	DH min [mm] - (min hole diameter)	DH min (최소 홀 직경)
16	5.9°	3	7,6	22	30
20	3.4°	3	11,6	30	38
25	2.2°	3	16,6	42	50
32	1.4°	3	23,6	54	62
35	1.3°	3	23,6	60	68
NOTE: Maximum ramp angle decreases as nose radius increases.

7792 Series IC06 • Ramping Application Data • Curved Edges • Inch
D1 max	램핑 각도 (°)	a_e 최대 플런징	페이싱 피치	DH min [Inch] - (min hole diameter)	DH min (최소 홀 직경)
0.63	8.2°	0.118	0.26	0.856	1.171
0.75	6.7°	0.118	0.38	1.106	1.421
1.00	4.3°	0.118	0.63	1.606	1.921
1.25	2.6°	0.118	0.88	2.106	2.421
NOTE: Maximum ramp angle decreases as nose radius increases.

7792 Series IC06 • Ramping Application Data • Straight-Edged Inserts • Inch
D1 max	램핑 각도 (°)	a_e 최대 플런징	페이싱 피치	DH min [Inch] - (min hole diameter)	DH min (최소 홀 직경)
0.63	7.2°	0.118	0.282	0.856	1.171
0.75	4.8°	0.118	0.380	1.106	1.421
1.00	2.5°	0.118	0.630	1.606	1.921
1.25	1.7°	0.118	0.880	2.106	2.421
NOTE: Maximum ramp angle decreases as nose radius increases.

7792 Series IC06 • Programing Data • Curved Edges • Metric [mm]
IC	코너R	R	L
06	0,8	1,37	0,4
09	0,8	2,01	0,73
	1,2	2,27	0,67
12	0,8	2,5	1,02
	1,2	2,73	0,97
16	1,2	4,18	1,46
7792 Series IC06 • Programing Data • Straight-Edged Inserts • Metric [mm]
IC	코너R	R	L
06	0,8	1,46	0,529
09	0,8	2,13	1,025
	1,2	2,25	0,95
12	0,8	2,46	1,33
	1,2	2,79	1,27
	2	3,42	1,13
16	1,2	3,56	1,82
CNC Program • Corner Radius Definition The use of common CAD/CAM systems requires a round insert dimension to be known for cavity machining. For finish pass applications: Wiper facet for finishing use max. feed 0,8mm.

7792 Series IC06 • Programing Data • Curved Edges • Inch [inch]
IC	코너R	R	L
06	0.031	0.057	0.016
09	0.031	0.079	0.028
	0.047	0.089	0.026
12	0.031	0.098	0.040
	0.047	0.107	0.038
16	0.047	0.164	0.057
7792 Series IC06 • Programing Data • Straight-Edged Inserts • Inch [inch]
IC	코너R	R	L
06	0.031	0.057	0.021
09	0.031	0.084	0.040
	0.047	0.088	0.037
12	0.031	0.097	0.052
	0.047	0.109	0.050
	0.079	0.134	0.044
16	0.047	0.140	0.072
CNC Program • Corner Radius Definition The use of common CAD/CAM systems requires a round insert dimension to be known for cavity machining. For finish pass applications: Wiper facet for finishing use max. feed 0.031".

자세히 읽기View Less

You are about to leave the Solution building process.

Are you sure you want to leave?

제품 번호	5681122
ISO 카탈로그 ID	7792VXP06SA020Z3R35
ANSI 카탈로그 ID	7792VXP06SA020Z3R35
Grade	S
[D1MAX] Maximum Cutting Diameter	20 mm
[D1MAX] Maximum Cutting Diameter	.787 in
[D1] Effective Cutting Diameter	11.6 mm
[D1] Effective Cutting Diameter	.457 in
[L2] Head Length	35 mm
[L2] Head Length	1.378 in
[G3X] Connection Thread Size External	M10
[DPM] Pilot Diameter Machine Side	10.5 mm
[DPM] Pilot Diameter Machine Side	.4134 in
[AP1MAX] 1st Maximum Cutting Depth	0.9 mm
[AP1MAX] 1st Maximum Cutting Depth	.035 in
[Z] Number of Flutes	3

환영합니다

기본 설정을 확인해 주십시오

기본 설정 업데이트

제품 제안

Product Family suggestions

솔루션 수정

솔루션 추가

유사한 제품:

7792VXP06 Series • End Mill • Screw-On • Metric

High-Feed copy milling cutter for multiple materials.

제품 번호5681122

ISO 카탈로그 ID7792VXP06SA020Z3R35ANSI 카탈로그 ID7792VXP06SA020Z3R35

공작물 재료

사용 및 응용 분야

특징 및 장점

인서트 선택

인서트 선택 가이드 • IC 06

이송량

속도

권장 초기 속도[m/min]

애플리케이션 데이터

제품 제안

Product Family suggestions

알림

유사한 제품:

7792VXP06 Series • End Mill • Screw-On • Metric

High-Feed copy milling cutter for multiple materials.

제품 번호5681122

ISO 카탈로그 ID7792VXP06SA020Z3R35ANSI 카탈로그 ID7792VXP06SA020Z3R35

Sending to {{cadTool}} in progress...

공작물 재료

사용 및 응용 분야

특징 및 장점

인서트 선택

인서트 선택 가이드 • IC 06

이송량

속도

권장 초기 속도[m/min]

애플리케이션 데이터

The following files are available